Texas Instruments AM3352 Sitara 800MHz ARM Cortex-A8 CPU 256MB DDR3 SDRAM, 256MB Nand Flash Serial ports, USB Host, USG OTG, CAN, 2x RS485, microSD, LCD interface, Audio, 2x Gigabit Ethernet Optional 4.3" (480×272) touchscreen LCD available (this CPU does not have a 3D graphics accelerator) Supports Linux 3.2.0 Supports -40 to +85 °C industrial temperature range operation The MYD-AM3352-J is a high-performance ARM development board with a plug-in DIMM module that contains an 800MHz Texas Instruments Sitara AM3352BZCZA80 ARM Cortex-A8 Microprocessor producing high DMIPS at a low cost while also delivering key peripherals. The MYD-AM3352-J's CPU module comes with Linux pre-installed. The system is constructed of a motherboard plus a core board that is plugged into an SO-DIMM 200-pin slot and can be removed and replaced. As well as the CPU itself, the core board contains a Gigabit Ethernet PHY, 256MB NAND Flash, 256MB DDR3 SDRAM, 32Kb EEPROM, and a power management IC. The base board provides many peripheral interfaces and extended controller chips. These include a Debug port, USB Host port, USB OTG port, dual Gigabit Ethernet ports, one CAN, two RS485, one microSD, Audio in/out, Buzzer, WiFi, LCD, Touchscreen, JTAG, and other peripheral signals on extension interfaces. The board comes with a Linux 3.2.0 software package, detailed documentation, and all necessary cables. At the bottom of this page, you can add an optional LCD touchscreen. AM3352 Development Board Features  - TI AM3352BZCZA80 Sitara 800MHz ARM Cortex-A8 32-bit RISC MPU with NEON SIMD co-processor, 32KB/32KB L1 Instruction Cache, 256KB L2 Cache
- 256MB DDR3 SDRAM and 256MB NAND Flash (on CPU module)
- Gigabit Ethernet PHY (one on CPU module)
- Red Power LED and Green User LED (on CPU module)
- TPS65217C power management IC (on CPU module)
- 32Kb EEPROM (on CPU module)
- 3-wire RS232 Serial Port
- Four 5-wire RS232 Ports
- Two RS485 interfaces, with isolation; multiplexed with UART2 and UART3
- USB Debug Serial Port
- USB2.0 Host Port
- USB2.0 OTG Port (mini-USB)
- Two 10/100/1000Mbps Ethernet Interfaces, RJ45
- CAN Bus interface, with isolation
- microSD (TF) Card Slot
- LCD Interface (16-bit true color)
- 4-wire Resistive Touch Screen Interface
- Audio Input Port, 3.5mm jack
- Stereo Audio Output port, 3.5mm jack
- Buzzer
- 2.0mm-pitch 10-pin JTAG interface
- Four Buttons (2 User, 1 Reset, 1 Power)
- One power LED (red) and two user LEDs (green)
- Real-Time Clock with battery backup capability
- 2mm-pitch 2×10-pin and 2mm-pitch 2×5-pin Expansion Headers (3x ADC, 1x SDIO, 1x I2C, 1x UART, 8x GPIO)
- Power Requirements: 5V @ 2A; CPU module only 5V @ 0.8A
- Dimensions: 106 × 177 mm
- 4-layer PCB main board; 8-layer PCB CPU module
AM335x Development Board Linux Software Note: The same software package is provided for every system in the MYD-AM335x-J series. Some drivers and examples may not be supported by certain CPUs. | Category | Name | Description | | Bootloader | U-boot | Responsible for system initialization and boot kernel, including TCP/IP (with source code) | | Kernel | Version | Linux 3.2.0, customized (with source code) | | Drivers | USB Host | USB Host driver supporting OHCI and EHCI (with source code) | | USB Device | USB Device driver (with source code) | | Ethernet | Ethernet driver (with source code) | | MMC/SD | MMC/SD card driver (with source code) | | NAND Flash | NAND Flash / SmartMedia driver (with source code) | | I2C | I2C driver (with source code) | | SPI | SPI driver (with source code) | | Audio | SGTL5000 driver (with source code) | | LCD Controller | LCD driver, supports 4.3-inch or 7-inch TFT LCD (with source code) | | RTC | RTC driver (with source code) | | TouchScreen | 4-wire Resistive Touch driver (with source code) | | PWM | PWM driver (with source code) | | UART | Serial driver (with source code) | | CAN | CAN driver (with source code) | | PMU | Power Management Unit driver (with source code) | | LED | GPIO/PWM LED driver (with source code) | | GPIO | LED driver and GPIO (with source code) | | I2C to UART/IO | I2C to UART/IO driver (with source code) | | File System | rootfs | Based on buildroot, provided in binary | | rootfs-qt | Qt filesystem, provided in binary | | Demos | Audio | Audio test program (with source code) | | Key&LED | Button and LED test program (with source code) | | NET | Ethernet demo (with source code) | | RTC | Real-Time Clock test experiment (with source code) | | NAND Flash | NAND Flash test (with source code) | | GPIO | LCD test program (with source code) | | RS485 | RS485 test (with source code) | | Qt | Qt Kit and Qt demo (with source code) | AM3352 Development Board Package Contents - MYD-AM3352-J-I Board (with MCC-AM3352-J-I Module)
- 12V, 1.5A Power Adapter
- Ethernet cable
- USB cable
- DVD-ROM with schematic, user manual, BSPs and source code
AM3352 Development Board Resources Ships from: China
Lead time: 1 week The LCD Display option below allows you to add a 4.3-inch (480×272) LCD touchscreen to your order. Note that the LCD module has an operating temperature range of -20 to +70 °C. The checkboxes allow you to add extra or alternative CPU modules.
Available Options:
| LCD Display: |
|
Optional Recommended Products for this Item
|
