The MYD-IMX287-I is a power-efficient ARM Evaluation Kit for the Freescale i.MX28 family of multimedia application processors which have an ARM926EJ-S core and run at up to 454 MHz. The kit features a development board with a removable CPU module as the core controller board. It runs the Linux operating system. You can use this system as a reference platform to start your design. The main board lets you get the most out of the i.MX28x processor, providing a comprehensive set of peripherals and connectivity options, making this system suitable for smart gateways, human-machine interfaces, hand-held devices, educational tools and other industrial applications.

This version of the system has an extended industrial operating temperature range of -40 to +85 °C.

The MYD-IMX28x-I Development Board supports one of two CPU modules. With this kit, it will include the MYC-IMX287-I System on Module (SOM) integrated with the i.MX287 processor, 128MB DDR2 SDRAM, 256MB Nand Flash and Ethernet PHY. It is connected to the base board through two 1.27mm-pitch 80-pin connectors. The base board extends many peripherals and interfaces through headers and connectors, including 1x RS232, 1x Debug, 2x USB ports, 2x Ethernet, 2x CAN, 1x RS485, microSD, Audio, LCD, JTAG, etc.

At the bottom of this page, you can add the alternative i.MX283 CPU module to your order, allowing you to swap out the two processors to evaluate them both on the same base board. The differences between the two available processors are as follows:

	Ethernet	L2 Switch	CAN	S/PDIF Tx	Kit with Base Board
i.MX283	1x				MYD-IMX283-I
i.MX287	2x	Yes	2x	Yes	This kit

i.MX287 Development Board Features

• Freescale i.MX287 Multimedia Applications Processor, 454 MHz ARM926EJ-STM core with 16KB instruction cache, 32KB data cache, 128KB on-chip SRAM, 128KB on-chip ROM, 1280 bits on-chip OTP ROM
• 128MB DDR2 SDRAM, 256MB Nand Flash and 128KB SPI Data Flash (on CPU module)
• Ethernet PHY (on CPU module)
• Red Power LED and Blue User LED (on CPU module)
• CPU module connects to main board via two 1.27mm-pitch 2×40-pin headers
• 3-wire RS232 Debug Serial Port, DB9
• 5-wire RS232 Serial Port, UART0, DB9
• RS485 Interface
• USB2.0 Host Port
• USB2.0 OTG Port
• Two 10/100Mbps Ethernet Interfaces, RJ45
• Two CAN Bus Interfaces
• microSD (TF) Card Slot
• LCD Interface (16-bit true color)
• 4-wire Resistive Touch Screen Interface
• Audio Input Port, 3.5mm jack
• Stereo Audio Output Port, 3.5mm jack
• Headphone Output Port, 3.5mm jack
• Built-in Microphone
• Buzzer
• 2.54mm-pitch 20-pin JTAG Interface
• Four Buttons (3 User, 1 Reset)
• Two User LEDs (blue)
• Two 2mm-pitch 2×10-pin Expansion Headers (1x High-Speed ADC, 2x Low-Resolution ADC, 1x SPI, 2x I2C, 3x UART, 3x PWM)
• Power Requirements: 5V for main board; 3.3V for CPU module by itself
• Dimensions: 140 × 90 mm (CPU module by itself measures 62 × 38 mm)
• 4-layer PCB main board; 6-layer PCB CPU module

i.MX287 Development Board Software

i.MX287 Development Board Package Contents

• MYD-IMX28x-I Main Board with MYC-IMX287-I CPU Module
• 5V, 2A Power Adapter
• Ethernet cable
• Serial cable
• USB cable
• DVD-ROM with schematic, user manual, BSPs and source code

i.MX287 Development Board Resources

• MYD-IMX28x-I Main Board Dimensions
• MYD-IMX28x-I Main Board Block Diagram
• MYC-IMX28x-I CPU Module Dimensions
• MYC-IMX28x-I CPU Module Block Diagram
• MYC-IMX28x-I CPU Module Pinout (some functions may not be applicable to alternative i.MX283 CPU)
• Schematic of optional 4.3-inch LCD touchscreen
• Schematic of optional 7-inch LCD touchscreen
• Freescale i.MX287 Page with datasheet and other documentation

Ships from: China
Lead time: 1 week

The options below allow you to add a 4.3-inch (480×272) or 7-inch (800×480) LCD touchscreen to your order (the industrial operating temperature range of this system does not apply to the optional LCDs, whose operating range is -20 to +70 °C). Also, you can use the checkbox below to order additional CPU modules at a discount over purchasing them separately. (You can change the quantity during checkout — just make sure to click Update after changing the number in the box, or the quantity will not be updated.)