Extra Hand-Held 8-Way Field and Production Programmer for Microchip PIC12F, PIC16F and PIC18F microcontrollers
To load program code into this Handheld Programmer, you need the PIC Hand-Held 8-Way Programmer Starter Kit or the single-target PIC Hand-Held Programmer Starter Kit.
The ultimate programming tool for PIC12F, PIC16F and PIC18F microcontrollers, in the field or on the production line — so easy a child can use it! Just load it once with up to eight programs and then program target devices again and again.
You need just one starter kit for your PC, then you can load as many programmers as you require.
Simply connect the starter kit dongle to your USB port and run the master software. Select your code file, device type and settings, and now you can load the programmer with your program or test code in seconds. As the programmer is battery powered during load, you don't need any power supplies or cabling; just plug a programmer into the lead supplied. Once a programmer is loaded, it is completely portable and can be used where you need it — not where your PC is located. The 8-way programmer can store up to eight different programs for different PIC microcontroller targets, selectable using a dial on the front of the programmer.
The Handheld Programmer features one-button operation, auto sensing of target, auto verification and an error indicator. In most cases, the target circuit does not need to be powered, and low-voltage targets are supported. It can power the target circuit at 3.3V or 5V. The programmer has 2MB of memory and is powered by a common 9V PP3 battery, or by an external power supply. If your target circuit requires more than 150 mA current, it must be self-powered or the programmer must be powered by an external supply.
When it's time to program new code into your devices, simply reconnect the handheld programmer to the PC, load the new code into it, and you're ready to go again.
Hand-Held PIC Programmer Features
- PIC Hand-held programmer uses 9V PP3 battery or power supply
- Single-button operation
- Reload new programs as often as you need
- Holds program code indefinitely
- Low or High Voltage programming
- 10-way DIL and 6 × 1-way flying lead connectors included
- Program/Verify Flash or EEPROM or both
- Program and verify Configuration Bytes and User ID
- Existing EEPROM Data can be preserved
- Powers target device (up to 150mA) at 3.3V or 5V
- For families that are low-voltage only (e.g. PIC18FxxJ and some PIC18FxxK), programmer uses 3.3V for them
- Note: Some PIC16Fxxx devices need 4.5V minimum for chip erase, so programmer always uses 5V for these
- Dimensions: Metric — 106mm × 58mm × 25mm
- Dimensions: Imperial — 4.5 × 2.5 × 1 inches
- 2MB memory
PIC Handheld Programmer Supported Devices PIC18F microcontrollers
- PIC18FxxKxx (9V VPP) except K90 and 6x/8xK22
- Also supports LF versions
- PIC12F1822, PIC12F1840
- PIC12F609, PIC12F615
- PIC12F635, PIC12F683
- Also supports LF versions
- PIC16F627A, PIC16F628A, PIC16F648A (HVP only if Reset pin is not reprogrammed as I/O)
- PIC16F631, PIC16F636, PIC16F639
- PIC16F68x, PIC16F690
- PIC16F193x (HVP only)
- PIC16F182x (HVP only) Note: Not all devices have LVP mode.
Free updates are available for new device support. This list is current as of 4 January 2013.
- PIC16F5x will be supported in a future update
Power Supply If you do not want to use the internal 9V PP3 battery, the power supply required is 9V with a 5.0/2.1mm Barrel connector. See below for optional universal power supplies that can be used in most countries.
Designing the Handheld Programmer into Your Product To use a handheld programmer to configure your product in the field or on the production line, you need to have a 10-way box connector or just use the 6-way flying lead adapter.
The header has 0.1-inch (2.54mm) pin spacing. The GND pins marked with an asterisk (*) must be connected to target ground. Either or both of the other GND pins also must be connected to target ground. VDD must be connected to the target circuit's Vdd. The PGM pin is only used for LVP mode.
For more information, see the 8-way PIC Handheld Programmer Quick Start Guide (assumes you have a starter kit).
To use this Handheld Programmer, you need the PIC Hand-Held 8-Way Programmer Starter Kit. The starter kit includes one of these programmers. This order page is for owners of a starter kit who wish to purchase additional programmers.
Optional Recommended Products for this Item