The LAP-F1 series of logic and protocol analyzers is for high-speed, comprehensive measurements. They provide a high sample rate, deep memory and a large number of channels in a single instrument. The hardware features a Xilinx high-performance FPGA chip and exclusive active probes that enhance sampling accuracy and stability.

It includes an extensive protocol library of more than 110 built-in decoders, and straightforward software provides for efficient debugging. This hardware is optimized for complex circuits with high-frequency signals. It features a DSO connection and six hardware protocol triggers: I2C, I2S, SPI, SVID, UART, and CAN 2.0B.

The active probes provide good impedance matching, reduced crosstalk and noise, and reinforced ground to enhance measurement quality and to provide accuracy and stability with high-speed signals. They support DUT bandwidths of up to 200 MHz. Four types of probes are available. With your purchase you will receive a complete set of two types of your choice (general-purpose, low-voltage, or negative-logic) and four eMMC probes. Whichever type you don't choose still can be purchased separately. See the bottom of this page for a feature comparison of the different probe types, the set selector, and links to individual extra probes.

The eMMC probes allow you to use the eMMC5.1/SD3.0 Trigger feature of the analyzer, which by default is limited to four channels. There is an optional eMMC license that will allow you to trigger and decode all eMMC5.1/SD3.0 signals. That option includes 28 additional eMMC probes.

LAP-F1 Series Features

Items / Type		LAP-F1404M	LAP-F1408M	LAP-F14016M	LAP-F14032M	LAP-F14064M	LAP-F1644M	LAP-F1648M	LAP-F16416M	LAP-F16432M	LAP-F16464M
Channels		40	40	40	40	40	64	64	64	64	64
Memory depth per channel		4 Mbits	8 Mbits	16 Mbits	32 Mbits	64 Mbits	4 Mbits	8 Mbits	16 Mbits	32 Mbits	64 Mbits
Memory depth / channels when using Channel Folding		4Mb / 40 ch 8Mb / 16 ch 16Mb / 8 ch 32Mb / 4 ch 64Mb / 2 ch 128Mb / 1 ch	8Mb / 40 ch 16Mb / 16 ch 32Mb / 8 ch 64Mb / 4 ch 128Mb / 2 ch 256Mb / 1 ch	16Mb / 40 ch 32Mb / 16 ch 64Mb / 8 ch 128Mb / 4 ch 256Mb / 2 ch 512Mb / 1 ch	32Mb / 40 ch 64Mb / 16 ch 128Mb / 8 ch 256Mb / 4 ch 512Mb / 2 ch 1Gb / 1 ch	64Mb / 40 ch 128Mb / 16 ch 256Mb / 8 ch 512Mb / 4 ch 1Gb / 2 ch	4Mb / 64 ch 8Mb / 32 ch 16Mb / 16 ch 32Mb / 8 ch 64Mb / 4 ch 128Mb / 2 ch 256Mb / 1 ch	8Mb / 64 ch 16Mb / 32 ch 32Mb / 16 ch 64Mb / 8 ch 128Mb / 4 ch 256Mb / 2 ch 512Mb / 1 ch	16Mb / 64 ch 32Mb / 32 ch 64Mb / 16 ch 128Mb / 8 ch 256Mb / 4 ch 512Mb / 2 ch 1Gb / 1 ch	32Mb / 64 ch 64Mb / 32 ch 128Mb / 16 ch 256Mb / 8 ch 512Mb / 4 ch 1Gb / 2 ch	64Mb / 64 ch 128Mb / 32 ch 256Mb / 16 ch 512Mb / 8 ch 1Gb / 4 ch
Operating System		Windows 8.1 (recommended), Windows 7, Windows Vista, Windows XP, Windows 2000 — (32- or 64-bit versions supported)
Transmission		USB 3.0 (2.0 compatible)
Sample rate	Internal (timing) max	1 GHz
	External (state) max	32
Trigger	Trigger Channels	32 (channels divided into 2 groups; or triggering between 1st group (32 ch) and 2nd group (8/32 ch)
	Trigger Events	Pattern / Edge / Pulse-width / Interval (time)
	Trigger Delay	Yes
	Trigger Sequence	256 Levels
	Trigger Pass	1 to 65535
	Trigger Voltage	4 simultaneous levels; 1 for each of the 4 ports
	Auxiliary Cursors	250
	Hardware Triggers	I2C, I2S, SPI, SVID, UART, CAN 2.0B
	eMMC5.1/SD3.0 Trigger	4 ch. can be triggered/sampled/decoded at 2GHz in standard package; see Optional Functions below for details about getting full support
Software Functions	Languages	English, Simplified Chinese, Traditional Chinese
	Zooming & Panning	2 cursor modes
	Waveform & UI Customization	Modify appearance of channels, menus, traces, windows, etc.
	State List & Waveform View	Present samples as list of 1s and 0s, or as waveform
	DSO Connection	Connect to and import signals from DSOs
	File Comparison	Compare 2 files to see where and how they differ
	Navigator	Quickly navigate to distant parts of the waveform
	Memory View	See what the memory looks like; what is read/written to which address
	Packet List	Breakdown of all packets in list form
	Statistics	Table view showing number of periods, periods that satisfy conditions, etc.
	Real-time Signal Activity	Live view of probe activity
	Protocol Decoders	More than 110 free built-in protocol decoders
Phase Errors		Less than 3ns
Power		AC in: 100-240V @ 50/60Hz; DC out: 9V/5.55A
Dimensions		322 × 180 × 38 mm
Certifications		CE, FCC
Optional Functions	Channel Folding	As seen above, you can activate this free option to give your LAP-F1 unit the ability to concentrate the total memory on a limited number of channels. For example, with this 40-channel version with 64Mb per channel, you could enable only 16 channels to get 128Mb per channel, or enable only 8 channels to get 256Mb per channel, etc.
	eMMC5.1/SD3.0	Purchase this option to unlock 32-channel 2GHz sampling and the ability to trigger and decode all signals of eMMC5.1/SD3.0. An additional 28 probes are included with purchase of this option, to give you a total of 32. As eMMC has only 11 signals, the remaining signals can be used for other high-speed acquisitions.
	Long-time Record	Firmware option (separate purchase) to unlock the ability to stream samples directly to disk. Up to 40 channels can be streamed at an average rate of 300MB/s using USB 3.0. The long-time record function can be used to acquire signals from 7 hours up to a month depending on your sampling setup. Note that a fairly powerful PC is required to run this function reliably.

Built-in protocols

• Automotive — CAN 2.0B, DSI Bus, FlexRay 2.1A, LIN 2.1, MVB, WTB
• PC System — FWH, GPIB, Low Pin Count, LPC-SERIRQ, LPT, PCI, PECI, PS/2, SVID, USB 1.1, USB 2.0
• Memory — Compact Flash 4.1, I2C (EEPROM 24L), I2C (EEPROM 24LCS61/24LCS62), MICROWIRE (EEPROM 93C), SD2.0/SDIO, SAMSUNG K9 (NAND Flash), SPI Compatible (Atmel Memory), UNI/O
• Digital Audio — AC97, DSA Interface, HD Audio, HDMI CEC, I2S, MIDI, PCM, PSB Interface, S/PDIF, STBus
• IC Interface — 1-WIRE, 1-Wire (Advanced), 3-WIRE, BDM, HPI, I2C, JTAG 2.0, MCU-51 DECODE, MICROWIRE, SLE4442, SSI Interface, ST7669, SPI, SPI PLUS, Serial Wire Debug (SWD), UART (RS-232C/422/485)
• Basic Logic Application — ARITHMETICAL LOGIC, DIGITAL LOGIC, JK FLIP-FLOP, UP DOWN COUNTER
• Infrared Rays — IRDA, NEC PD6122, Philips RC-5, Philips RC-6, PT2262/PT2272
• Optoelectronics — 7-SEGMENT LED, CCIR656, CMOS IMAGE, DALI Interface, DM114/DM115, DMX512, LCD12864, LCD1602, LG4572, S2Cwire/AS2Cwire, SCCB
• Power — BMS, HDQ, PMBus 1.1, SDQ, SMBus 2.0
• Wireless — Differential Manchester, DigRF, ISO7816 UART, KEELOQ Code Hopping, MANCHESTER, MII, MILLER, MIL-STD-1553, MODIFIED MILLER, SIGNIA 6210, SWP, WIEGAND, WWV/WWVH/WWVB
• Other — DS1302, DS18820, HART, KNX, ModBus, MODIFIED SPI, OPENTHERM 2.2, PROFIBUS, SHT11, YK-5

LAP-F1 40-channel Series Package Contents

• LAP-F1 logic analyzer hardware
• CD with software and user manual
• 20 Low voltage probes (two channels per probe)
• Four eMMC probes
• One eMMC Clock-In probe
• 25 USB 3.0 cables for connection to probes, A-to-A type, 32.5 cm
• 40 signal/ground cable pairs, 7.5 cm
• 80 clip-on connectors
• USB 3.0 cable for connection to PC, A-to-B type, 1.5 m
• 9V power supply with detachable 1.8 m cable
• BNC cable, 1 m
• UTB300 Combo PCI-e 4x card to give your PC two USB 3.0 ports and two SATA-III ports

Probe Specifications

Model Name	P100ST (General Purpose)	P120LV (Low Voltage)	P120NE (Negative Logic)	P200EM (eMMC/SD)
Included in base purchase	Yes, if chosen below	Yes, if chosen below	Yes, if chosen below	4 included in base purchase
Signal type	Single-ended bus	Single-ended bus	Single-ended bus	Single-ended bus
Channels (max)	64	64	64	32
Input Impedance / Capacitance	530 kOhm ±10% 8.2pF ±2pF	190 kOhm ±10% 4.3pF ±2pF	190 kOhm ±10% 4.3pF ±2pF	190 kOhm ±10% 4.3pF ±2pF
DUT Bandwidth (max)	100 MHz	120 MHz	120 MHz	200 MHz
Transmission Rate (max)	100 Mbit/s	120 Mbit/s	120 Mbit/s	400 Mbit/s
Trigger Voltage	User defined	User defined	User defined	User defined
Bus Voltage	VIH: 2V to 5V	VIH: 0.6V to 5V	VIH: 0.3V to 5V or VIH: -0.2V to -1.5V	VIH: 0.6V to 5V
Input Signal Level	-5V to +5V	0V to 5V	-5V to +5V	0V to 5V
Input DC Voltage (max)	±5V	±10V	±10V	±10V

LAP-F Series Logic Analyzer Resources

• LAP-F Series User Manual
• ZP-Logic Software