The im1RL has a single 12V, 7A Relay with relay-driving circuitry. The relay can be controlled by 3.3V or 5V logic, making it suitable for Modtronix boards, Arduino, AVR, Microchip PIC or nearly any other project that requires a relay.
This module makes the three relay outputs (Common, Normally Open, Normally Closed) available via a 3.5mm Pluggable Terminal Block connector. The center pin of the connector is Common; left (viewing connector from the front) is Normally Closed; and the right is Normally Open. They are also marked on the PCB with symbols.
Relay Add-on Board Features
- One 12V, 7A high-quality relay
- Relay-driving and diode-protection circuitry
- High-quality, 3.5mm terminal block connector consisting of a header and plug
- Can be used in an iMod port (see below)
- Different pin header options available (see below)
- Module dimension: 24.8 × 22.2 mm (0.975 × 0.875 inches)
High-quality Components Only high-quality components from reputable suppliers are used in the manufacture of this module. All components have been selected to exceed the maximum rated specifications.
- 12V, 7A Relay: Manufacturer is either NCR, Hongfa, Hsinda, Songle, Goodsky or Toward.
- 100mA Digital Transistor: Manufacturer is either Infineon, NXP Semiconductors, Micro Commercial, Diodes Inc or Rohm.
- Dual Diode, Common Anode, 150mA, 90V: Manufacturer is either ON Semiconductors, NXP Semiconductors, Micro Commercial or Diodes Inc.
iMod Pin Configuration This is an iMod module with 0.7" pin column width, meaning it uses a standard pinout and configuration that allows it to be connected easily to any host board that has an iMod port. This includes the Modtronix SBC83I, SBC66UAL, and the various PT66E Prototyping Add-ons for other boards in the SBC66 series.
The pin pitch is 0.1" so you can use the module also on any typical prototyping board or breadboard.
Here is some example code for the Netcruzer (SBC66/SBC66+PT66) boards that shows how to turn the relay on and off, assuming this module is mounted in iMod port 1:
imod1_ConfDirPin2(OUTPUT_PIN); //Configure pin 2 of iMod 1 as an output
imod1_WritePin2(1); //Set pin 2 of iMod 1 - Turn relay on
imod1_WritePin2(0); //Clear pin 2 of iMod 1 - Turn relay off
For information about the iMod pinout, download this iMod Overview. Find other iMod modules in our iMod Category.
Pin Header Options Use the Headers option at the bottom of this page to select what type of pin headers you want included with the module and whether you want them included loose or pre-soldered. The default option is for common rectangular pins included loose, as shown in the picture above. All pin header types use 3mm long pins. As this module does not use iMod I/O ports 7-10, the header strips will be six pins long for each side.
Below the header option selector, you will see checkboxes for adding additional header strips, just in case, as well as socket strips that will mate with the Round Swiss pin header type. If you want to install the socket strips on your prototype so that you can plug in this module with Round Swiss pins, make sure to change and Update the quantity of sockets to 2 during checkout.
Download im1R-12V Schematic Download im1R-12V-TBP Dimensions Diagram
Optional Recommended Products for this Item
|Rectangular Pin Header, Male, 1x40 Single Row, 2.54mm Spacing||+|| US$0.75|
|6-pin Press-Fit Header Strip, Breakaway Pins, 2.54mm Pitch||+|| US$1.20|
|6-pin Swiss Header, Compact, Breakaway Pins, 2.54mm Pitch||+|| US$0.60|
|6-pin Swiss Socket, Compact, Breakaway Pins, 2.54mm Pitch||+|| US$0.66|