MicroController Pros Home Page My Account  Cart Contents  Checkout  
  Store » EM1000-TEV My Account  |  Cart Contents  |  Checkout   
Quick Find
Enter keywords to find the product you are looking for in the Quick Find field above

or use
Advanced Search
Accessory Boards->
ADI Blackfin
Atmel AVR->
Cypress PSoC
Microchip PIC->
Silicon Labs
ST Microelectronics->
Texas Instruments->
Embedded Ethernet->
Embedded Software->
I/O Modules->
Parts & Components->
Pick & Place Tools
Programmable Logic (PLD)
Prototype PCBs->
ROM/Flash Emulators
Test & Measurement->
Tutorial Software
Universal Programmers->
Intro to Embedded Tools
Embedded News Digest
Useful Resources
Shipping & Returns
Warranty & Liability
Privacy Notice
Conditions of Use
Contact Us

Back to 4x Serial to Ethernet Terminal Evaluation Kit Ordering Page

The TEV-IB0 implements one RS232/422/485 serial port. The port is built around SIPEX SP334 multi-protocol transceiver IC. A small PIC10F200 microcontroller from MICROCHIP is also used. This microcontroller replaces discreet logic that would be needed to control the SP334 in different operating modes. Related datasheets, assembly program for the microcontroller, as well as the schematic diagram for the TEV-IB0 board can be found on Tibbo website.

Two switches are provided on the board for protocol selection. Switch 1 selects between RS232 and RS422/485 signal levels. Switch 2 selects half-duplex or full-duplex mode of operation. Note that these switches only control the operation of the SP334. Serial ports of the EM1000-TEV must be correctly preset for desired communication mode as well.

For your convenience, each TEV-IB0 board is supplied with a TB100 terminal block adaptor.

DB-9M connector pin assignment

Pin #(1)RS232 modePRS422 modeRS485 mode
1 --- RTS- (output) ---
2 RX (input) RX- (input) RX- (input)
3 TX (output) TX+ (output) TX+ (output)
4 DTR (output) TX- (output) TX- (output)
6 DSR (input) RX+ (input) RX+ (input)
7 RTS (output) RTS+ (output) ---
8 CTS (input) CTS+ (input) ---
9 --- CTS- (input) ---

Required initialization code in Tibbo BASIC application

This section assumes that you are familiar with Tibbo BASIC and TIDE software. These are documented in the Tibbo BASIC Programming Guide.

Correct preset of serial ports falls outside the scope of this manual. This section will only remind you that you need to set a correct serial port mode matching the mode selected by the switches of the TEV-IB0. For RS232 or RS422 mode, set ser.interface=PL_SER_SI_FULLDUPLEX. For the RS485 mode set ser.interface=PL_SER_SI_HALFDUPLEX.

Do not forget that all lines of the EM1000 are configured as inputs by default. Any line that should work as an output should be configured as such. This is done through the I/O (io.) object. The only exception is the TX line that becomes an output automatically once the serial port is enabled.

Back to 4x Serial to Ethernet Terminal Evaluation Kit Ordering Page

Shopping Cart more
0 items
What's New? more
Flowcode 7 "Test & Debugging" Feature Pack
Flowcode 7 "Test & Debugging" Feature Pack
Specials more
XBee ZigBee Module, 50mW, Series 2.5, RPSMA Antenna Connector
XBee ZigBee Module, 50mW, Series 2.5, RPSMA Antenna Connector
01. LCD 4-mux, 7 digits x 14 segments, progress bar, arrows
02. PIC16F628A-I/P Microcontroller, 18 DIP, 20 MHz
03. Atmel ATtiny2313-20PU AVR Microcontroller, 20 DIP, 20 MHz
04. LCD 4-mux, 7.1 digits x 7 segments, progress bar, arrows
05. USB-to-Serial Cable: 3.3V TTL, Audio Plug Type, Reverse RX/TX
06. 2x10 (20-pin) 0.1" pitch IDC Connector Flat Ribbon Cable, 15cm
07. USB Universal In-Circuit Programmer PIC AVR ARM MSP 8051 EEPROM
08. ARM JTAG Debugger & Programmer, parallel port
09. Power Supply 3-12V DC, U.S. plug, 6 connection tips
10. Power Supply 3-12V DC, US/UK/Euro/AU Plugs, 100-240VAC
Reviews more
Development System for 64- & 100-pin AVR, w/ ATmega128: BIGAVR6
This is a great board, you can learn a lot with it. Severa ..
4 of 5 Stars!
  Thursday 20 September, 2018   List of all our Products

Copyright © 2003-2017 MicroController Pros LLC
Powered by osCommerce