MicroController Pros Home Page My Account  Cart Contents  Checkout  
  Store » Wireless » ZigBee » XB24CZ7SIT-004 My Account  |  Cart Contents  |  Checkout   
Quick Find
 
Enter keywords to find the product you are looking for in the Quick Find field above

or use
Advanced Search
Categories
Accessory Boards->
8051->
ADI Blackfin
Arduino->
ARM->
Atmel AVR->
Cypress PSoC
Freescale->
FTDI->
Locktronics
Microchip PIC->
MIPS
Parallax->
Renesas
Silicon Labs
ST Microelectronics->
Texas Instruments->
Tibbo->
Books->
Displays->
E-Blocks->
EEPROM/EPROM/FLASH
Embedded Ethernet->
Embedded Software->
I/O Modules->
Parts & Components->
Pick & Place Tools
Programmable Logic (PLD)
Prototype PCBs->
Robotics
ROM/Flash Emulators
Test & Measurement->
Tutorial Software
Universal Programmers->
Wireless->
  434MHz & 2.4GHz
  900MHz
  Bluetooth
  GSM/GPS->
  RFID/NFC
  WiFi->
  ZigBee
  Waspmote->
  Antennas
Information
Intro to Embedded Tools
Embedded News Digest
Useful Resources
Shipping & Returns
Warranty & Liability
Privacy Notice
Conditions of Use
Contact Us
XBee S2C ZigBee Module, 6.3 mW, RP-SMA Connector US$25.00

XB24CZ7SIT-004
XBee S2C ZigBee Module, 6.3 mW, RP-SMA Connector


Wireless connectivity using the ZigBee protocol

XBee S2C embedded RF modules provide cost-effective wireless connectivity to devices in ZigBee mesh networks. Utilizing the ZigBee PRO Feature Set, these modules are interoperable with other ZigBee devices, including devices from other vendors.

Part of the XBee family of wireless products, these modules are easy to use, share a common footprint, and are fully interoperable with other XBee products utilizing the same technology. This allows different XBee technologies to be drop-in replacements for each other; you can switch between 802.11, 802.15.4, ZigBee, DigiMesh and proprietary long-range with minimal development time or risk.

Series 2 modules use a different hardware configuration from the earlier models. They are not compatible with the outdated ZNet Series 2.5 modules. You can, however, change the firmware of existing ZNet Series 2.5 modules to the new ZB Series 2 firmware.

This S2C module is a compatible replacement for the obsolete XB24-Z7SIT-004 module. The difference is the use of the newer EM357 wireless device in place of the obsolete EM250. This module also is pin compatible the obsolete XB24-BSIT-004 ZNet 2.5 module, but, as stated above, it is not over-the-air compatible unless the ZNet module's firmware is changed.

ZB Series 2 New Features

ZB offers many new and improved features over ZNet 2.5, including:
  • Data transmissions are resolved directly to APS unicasts. This provides the ability to send and receive ZDO commands.
  • NH command configures the unicast transmission timeout. This command can extend the number of unicast hops dramatically beyond the 6-8 hop limit that existed in ZNet 2.5.
  • ZS command allows ZigBee stack profile to be set as required.
  • Routers and coordinators can expire end-device children from their child tables if the end device has not polled within a settable timeout.
  • The ZA command is no longer needed. SE, DE and CI addressing commands are always enabled.
  • AI now includes several new values.

ZB S2C ZigBee Module Features

  • Transceiver: Silicon Labs EM357 SoC
  • RF data rate: 250 Kbps; Serial up to 1 Mbps
  • Interface data rate: 1200 bps to 1 Mbps (non-standard baud rates supported)
  • Indoor/Urban range: Up to 200 ft (60 m)
  • Outdoor/RF line-of-sight range: Up to 4000 feet (1200 m)
  • Power output: 3.1mW (+5 dBm); 6.3mw (+8 dBm) Boost Mode
  • Receiver sensitivity (1% PER): -100 dBm; -102 dBm Boost Mode
  • Serial data interface: UART, SPI
  • Configuration method: API or AT commands, local or over-the-air (OTA)
  • Frequency band: ISM 2.4 GHz
  • Interface immunity: DSSS (Direct Sequence Spread Spectrum)
  • ADC: Four 10-bit analog inputs
  • Digital I/O: 15 I/O lines
  • Operating temperature: -40C to +85C (industrial)
  • Size: 0.960 in 1.087 in (2.438 cm 2.761 cm)
  • Weight: 0.10 oz (3g)
  • Protocol: ZigBee PRO 2007, HA-Ready with support for binding/multicasting
  • Encryption: 128-bit AES
  • Error handling: Retries/Acknowledgments
  • Addressing: PAN ID, 64-bit IEEE MAC
  • Channel capacity: 16 Direct Sequence Channels (11 through 26)
  • Supply voltage: 2.1V to 3.6V DC (Footprint Recommendation: 3.0V - 3.4V DC)
  • Transmit current: 33 mA (@ 3.3V); 45 mA Boost Mode
  • Receive current: 28 mA (@ 3.3V); 31 mA Boost Mode
  • Sleep current: <1 A @ 25C
  • Networking topology: Mesh, point-to-point, point-to-multipoint, peer-to-peer
  • Certifications: FCC (USA), IC (Canada), ETSI (Europe), RCM (Australia and New Zealand)

ZB S2C ZigBee Module Resources


Optional Recommended Products for this Item
2.4GHz Duck Antenna RP-SMA - Large, 5 dBi+ US$9.95

This product was added to our catalog on Thursday 07 July, 2016.

Reviews

Customers who bought this product also purchased
Folding 915MHz 1/4 Wave Antenna, 2 dBi, SMA Connector, 105 mmFolding 915MHz 1/4 Wave Antenna, 2 dBi, SMA Connector, 105 mmUS$4.95

Shopping Cart more
0 items
What's New? more
Flowcode 7 "Mechatronics Pack" Feature Pack
Flowcode 7 "Mechatronics Pack" Feature Pack
US$42.00
Specials more
2N3906 PNP Transistor, 200mA/40V, TO-92 (10 pack)
2N3906 PNP Transistor, 200mA/40V, TO-92 (10 pack)
US$1.10
US$0.59
Tell A Friend
 

Tell someone you know about this product.
Notifications more
NotificationsNotify me of updates to XBee S2C ZigBee Module, 6.3 mW, RP-SMA Connector
Reviews more
Write ReviewWrite a review on this product!
  Wednesday 18 October, 2017   List of all our Products

Copyright © 2003-2017 MicroController Pros LLC
Powered by osCommerce