MicroController Pros Home Page My Account  Cart Contents  Checkout  
  Store » Displays » Display Controllers » gen4-PA My Account  |  Cart Contents  |  Checkout   
Quick Find
 
Enter keywords to find the product you are looking for in the Quick Find field above

or use
Advanced Search
Categories
Accessory Boards->
8051->
ADI Blackfin
Arduino->
ARM->
Atmel AVR->
Cypress PSoC
Freescale->
FTDI->
Locktronics
Microchip PIC->
MIPS
Parallax->
Renesas
Silicon Labs
ST Microelectronics->
Texas Instruments->
Tibbo->
Books->
Displays->
  LCD Displays->
  LED Displays
  OLED Displays
  Display Controllers
E-Blocks->
EEPROM/EPROM/FLASH
Embedded Ethernet->
Embedded Software->
I/O Modules->
Parts & Components->
Pick & Place Tools
Programmable Logic (PLD)
Prototype PCBs->
Robotics
ROM/Flash Emulators
Test & Measurement->
Tutorial Software
Universal Programmers->
Wireless->
Information
Intro to Embedded Tools
Embedded News Digest
Useful Resources
Shipping & Returns
Warranty & Liability
Privacy Notice
Conditions of Use
Contact Us
Programming Adapter and Breakout Board for gen4 Display Modules US$12.00

gen4-PA
Programming Adapter and Breakout Board for gen4 Display Modules


  • Programming adapter for 4D Systems gen4 Picaso and Diablo modules
  • micro-USB interface
  • Breakout for the 30-way FFC signals on the gen4 modules
  • Powers the gen4 display
  • The gen4-PA (Gen4 Programming Adapter) is compatible with all of the gen4 range of intelligent display modules which feature Picaso or Diablo16 graphics processors. It provides a quick and easy way to program the gen4 range, and also acts as a breakout for the GPIO, Audio and Programming signals on the gen4's FFC interface.

    The signals are made available via 2.54mm pitch (0.1) pads around the edge of the gen4-PA. It also groups the common 5-way signals found on other 4D Systems products (and the gen4-IB that comes with each gen4 module), for an easy interface to other products such as the Arduino Adapter and Raspberry Pi Adapter.

    The gen4-PA replaces the need for a separate standard programmer, such as the uUSB-PA5 or 4D Programming Cable. The gen4-PA has the circuitry found on the uUSB-PA5-II built into it, and features a microUSB jack for connection to your PC. (A micro-USB cable must be purchased separately.)

    Use the gen4-PA for programming your gen4 display modules, as an interface to a breadboard for prototyping, as an interface to the Arduino and Raspberry Pi adapters, or as an interface to virtually any host.

    gen4 Programming Adapter & Breakout Board Features

    • USB 2.0 compliant Full Speed 12Mbps maximum speed; Suspend supported
    • Hardware or Xon/Xoff handshaking supported; 300bps to 2Mbps
    • UART supports 5, 6, 7, or 8 data bits; 1, 1.5 or 2 stop bits; odd/even/mark/space or no parity
    • Power-on reset circuit
    • Virtual COM port drivers allow operation with existing COM port PC applications
    • USB powered
    • -40 to +85 C temperature range
    • Traffic/Operation LED indicates board status
    • Breakout pads of all the signals found on the gen4 30-way interface, in 2.54mm (0.1") spacing

    GPIO Signals

    The function of the GPIO signals differs between Picaso-based and Diablo-based gen4 modules, so the silkscreen on the back of the gen4-PA board is generalized. Refer to the following table to determine what each pin will do for your particular display module:

    How to determine which COM port is allocated in Windows

    When configuring the COM port for applications that need to communicate with the gen4-PA (e.g. the Workshop4 IDE), you'll need to know the COM port number that Windows has allocated to it. Go to the Control Panel in Windows, click on System to open System Properties. Then click the Hardware tab and the Device Manager button. Scroll down the list and open Ports (COM & LPT). There you will see the COM port number that has been allocated to the gen4-PA.

    gen4 Programming Adapter & Breakout Board Resources


    This product was added to our catalog on Thursday 23 June, 2016.

    Reviews

    Shopping Cart more
    0 items
    What's New? more
    Flowcode 7 "Misc Pack A" Feature Pack
    Flowcode 7 "Misc Pack A" Feature Pack
    US$42.00
    Specials more
    GSM/GPRS Module for Arduino
    GSM/GPRS Module for Arduino
    US$667.00
    US$89.00
    Tell A Friend
     

    Tell someone you know about this product.
    Notifications more
    NotificationsNotify me of updates to Programming Adapter and Breakout Board for gen4 Display Modules
    Reviews more
    Write ReviewWrite a review on this product!
      Monday 20 November, 2017   List of all our Products

    Copyright © 2003-2017 MicroController Pros LLC
    Powered by osCommerce