MicroController Pros Home Page
My Account  Cart Contents  Checkout  
  Store » Parts & Components » Power Supplies/Adapters » 710-0011-01 My Account  |  Cart Contents  |  Checkout   
Quick Find
 
Enter keywords to find the product you are looking for in the Quick Find field above

or use
Advanced Search
Categories
Accessory Boards->
8051->
ADI Blackfin
Arduino->
ARM->
Atmel AVR->
Cypress PSoC
Freescale->
FTDI->
Locktronics
Microchip PIC->
MIPS
Parallax->
Renesas
Silicon Labs
ST Microelectronics->
Texas Instruments->
Tibbo->
Books->
Displays->
E-Blocks->
EEPROM/EPROM/FLASH
Embedded Ethernet->
Embedded Software->
I/O Modules->
Parts & Components->
  Batteries & Chargers
  Buzzers
  Cables/Adapters->
  Cameras
  Chips/ICs
  Connectors
  Crystals
  Diodes
  IC Sockets
  Joysticks/Keypads
  LEDs
  Memory Cards
  Motor Drivers
  Power Supplies/Adapters
  Relays
  Resistors
  RTCs
  Sensors->
  Solar Cells
  Switches
  Transistors
  Voltage Regulators
  Generic Pin Converters
Pick & Place Tools
Programmable Logic (PLD)
Prototype PCBs->
Robotics
ROM/Flash Emulators
Test & Measurement->
Tutorial Software
Universal Programmers->
Wireless->
Information
Intro to Embedded Tools
Embedded News Digest
Useful Resources
Shipping & Returns
Warranty & Liability
Privacy Notice
Conditions of Use
Contact Us
OpAmp Experimenter Board, OPA172, Resistors Included US$18.00

710-0011-01
OpAmp Experimenter Board, OPA172, Resistors Included


The Schmartboard OpAmp Board makes it easy to assemble and experiment with op-amp circuits. It uses an OPA172 operational amplifier whose main features make it suitable for experimenting.

These features are:

  • Wide Supply Range: +4.5V to +36V, 2.25V to 18V
  • Low Offset Voltage: 0.2mV
  • Gain Bandwidth: 10 MHz
  • Input Range Includes the Negative Supply
  • Input Range Operates to Positive Supply
  • Rail-to-Rail Output
  • Low Noise: 7nV/√Hz
  • High Common-Mode Rejection: 120 dB
  • Low Input Bias Current: 8pA
  • Low Quiescent Current: 1.6mA per Amplifier

For your convenience, the board comes bundled with some components that you can put into the sockets two 0Ω resistors, two 5.1KΩ resistors, two 10KΩ resistors, and a 22pF capacitor. The resistors can be placed into positions marked R2 through R8; the capacitor can be placed in position C1. Between the sockets are solder pads in case you want to install SMD components instead.

Male header pins provide access to test points on the board, and a pair of jumper shunts is included for configuration.

The OpAmp Board can be operated with single or dual power supplies, and the 10MHz bandwidth makes it sufficient for most experimental circuits.

OpAmp Board Resources

Connect multiple Schmartboards together!

Every Schmartboard has small notches along its sides which allow you to connect any number of them together in any combination. Purchase a set of the Mechanical Bridge Interconnects available in the options below if you want to be able to combine your Schmartboards.


Optional Recommended Products for this Item
Mechanical Bridge Interconnects for SchmartBoard PCBs, 20 Pieces+ US$5.00

This product was added to our catalog on Wednesday 30 March, 2016.

Reviews

Shopping Cart more
0 items
What's New? more
Flowcode 7 for PIC, AVR, Arduino, ARM - Academic 10 User
Flowcode 7 for PIC, AVR, Arduino, ARM - Academic 10 User
US$769.00
Specials more
Atmel AVR STK500 Compatible Programmer, parallel port
Atmel AVR STK500 Compatible Programmer, parallel port
US$13.93
US$5.90
Tell A Friend
 

Tell someone you know about this product.
Notifications more
NotificationsNotify me of updates to OpAmp Experimenter Board, OPA172, Resistors Included
Reviews more
Write ReviewWrite a review on this product!
  Monday 21 August, 2017   List of all our Products

Copyright © 2003-2017 MicroController Pros LLC
Powered by osCommerce