MicroController Pros Home Page
My Account  Cart Contents  Checkout  
  Store » ARM » Boards » Add-On Boards » DEVKIT-ST1L My Account  |  Cart Contents  |  Checkout   
Quick Find
 
Enter keywords to find the product you are looking for in the Quick Find field above

or use
Advanced Search
Categories
Accessory Boards->
8051->
ADI Blackfin
Arduino->
ARM->
  Boards->
    All Boards
    ARM11
    ARM7->
    ARM9->
    Cortex-A
    Cortex-M->
    Header Boards/Modules
    Prototype Boards
    Raspberry Pi
    CAN
    Enclosure
    Ethernet
    FOX Board->
    HDMI
    IDE interface
    LCD
    Linux pre-loaded
    RS232
    RS422/RS485
    SD/MMC
    UEXT
    USB Device
    USB Host
    VGA
    Wireless
    Add-On Boards
  Books
  JTAG Debuggers->
  Programmers
  Software
  Starter & Evaluation Kits
Atmel AVR->
Cypress PSoC
Freescale->
FTDI->
Locktronics
Microchip PIC->
MIPS
Parallax->
Renesas
Silicon Labs
ST Microelectronics->
Texas Instruments->
Tibbo->
Books->
Displays->
E-Blocks->
EEPROM/EPROM/FLASH
Embedded Ethernet->
Embedded Software->
I/O Modules->
Parts & Components->
Pick & Place Tools
Programmable Logic (PLD)
Prototype PCBs->
Robotics
ROM/Flash Emulators
Test & Measurement->
Tutorial Software
Universal Programmers->
Wireless->
Information
Intro to Embedded Tools
Embedded News Digest
Useful Resources
Shipping & Returns
Warranty & Liability
Privacy Notice
Conditions of Use
Contact Us
Base Board for NZ32 STM32 Module, with Sockets Installed US$19.95

DEVKIT-ST1L
Base Board for NZ32 STM32 Module, with Sockets Installed


This is a base board for the NZ32-SC151 STM32L151RC ARM Cortex-M3 module. It breaks out the module's pins into female sockets constituting four iMod ports, and also breaks out the programming pins to allow for in-circuit debugging with an ST-LINK/V2-compatible programmer. (It is not a standard pinout, so you will need to connect the lines individually.)

The base board's iMod ports have sockets to support either 0.7" or 0.9" width iMod Modules, or even double-width iMod modules like the im4OLED shown in the picture below.

Example Application

This image shows the base board with an NZ32 module installed (middle) and three different iMod modules plugged in:

Configuration Jumpers

The base board has several solder jumpers on the bottom allowing it to be used for different applications. It is supplied with default solder jumpers that configure the board as follows:
  • The Vcc pin (iMod pin 15) of all iMod ports is configured for 3.3V.
  • iMod ports 1 and 2 are configured for SPI mode (pins 12, 13 & 14 of all iMod ports can be configured for I2C or SPI mode).
  • iMod port 4 is configured for I2C mode (pins 12, 13 & 14 of all iMod ports can be configured for I2C or SPI mode).
The board's schematic notes all the default solder jumper positions in blue.

NZ32 Base Board Resources


This product was added to our catalog on Wednesday 20 January, 2016.

Reviews

Shopping Cart more
0 items
What's New? more
Flowcode 7 "Test & Debugging" Feature Pack
Flowcode 7 "Test & Debugging" Feature Pack
US$54.00
Specials more
4-port USB2.0 Hub, Unpowered, ASUS Zenhub
4-port USB2.0 Hub, Unpowered, ASUS Zenhub
US$10.00
US$5.90
Tell A Friend
 

Tell someone you know about this product.
Notifications more
NotificationsNotify me of updates to Base Board for NZ32 STM32 Module, with Sockets Installed
Reviews more
Write ReviewWrite a review on this product!
  Friday 28 April, 2017   List of all our Products

Copyright © 2003-2017 MicroController Pros LLC
Powered by osCommerce