MicroController Pros Home Page
My Account  Cart Contents  Checkout  
  Store » im232P-TBP My Account  |  Cart Contents  |  Checkout   
Quick Find
 
Enter keywords to find the product you are looking for in the Quick Find field above

or use
Advanced Search
Categories
Accessory Boards->
8051->
ADI Blackfin
Arduino->
ARM->
Atmel AVR->
Cypress PSoC
Freescale->
FTDI->
Locktronics
Microchip PIC->
MIPS
Parallax->
Renesas
Silicon Labs
ST Microelectronics->
Texas Instruments->
Tibbo->
Books->
Displays->
E-Blocks->
EEPROM/EPROM/FLASH
Embedded Ethernet->
Embedded Software->
I/O Modules->
Parts & Components->
Pick & Place Tools
Programmable Logic (PLD)
Prototype PCBs->
Robotics
ROM/Flash Emulators
Test & Measurement->
Tutorial Software
Universal Programmers->
Wireless->
Information
Intro to Embedded Tools
Embedded News Digest
Useful Resources
Shipping & Returns
Warranty & Liability
Privacy Notice
Conditions of Use
Contact Us
RS232 Interface 0.7" iMod Module, 3.5mm Pluggable Screw Terminal US$8.95

im232P-TBP
RS232 Interface 0.7\" iMod Module, 3.5mm Pluggable Screw Terminal


The im232P is an RS-232 interface module. It converts TTL logic levels to RS-232 interface levels, and vice versa. It has an operating voltage of 3.0V to 5.5V, low power consumption, and is ESD protected up to 15kV. It enables 3.3V and 5V devices (e.g., a microcontroller) to communicate via the standard RS-232 protocol. It uses the Sipex SP3232EEN RS-232 transceiver chip.

This module makes the five pins (0V, TX, RX, RTS, CTS) available via a 5-pin, 3.5mm Terminal Block connector; a plug-in block with screw terminals is included. The connections are marked on the PCB.

RS232 Interface Add-on Board Features

  • Meets True EIA/TIA-232-F Standards from a +3.0V to +5.5V Power Supply
  • Interoperable with EIA/TIA-232 and Adheres to EIA/TIA-562 Down to a +2.7V Power Source
  • Minimum 120kbps Data Rate under Load
  • Regulated Charge Pump Yields Stable RS-232 Outputs Regardless of VCC Variations
  • Enhanced ESD Specifications:
    15kV Human Body Mode
    15kV IEC1000-4-2 Air Discharge
    8kV IEC1000-4-2 Contact Discharge
  • High-quality 3.5mm terminal block connector consisting of a header and a plug
  • Can be used in an iMod port (see below)
  • Different pin header options available (see below)
  • Module dimensions: 22.2 19.7 mm (0.875 0.775 inches)
  • Operating Temperature: -40 to +85 C

iMod Pin Configuration

This is an iMod module with 0.7" pin column width, meaning it uses a standard pinout and configuration that allows it to be connected easily to any host board that has an iMod port. This includes the Modtronix SBC83I, SBC66UAL, and the various PT66E Prototyping Add-ons for other boards in the SBC66 series.

The pin pitch is 0.1" so you can use the module also on any typical prototyping board or breadboard.

For information about the iMod pinout, download this iMod Overview. Find other iMod modules in our iMod Category.

Pin Header Options

Use the Headers option at the bottom of this page to select what type of pin headers you want included with the module and whether you want them included loose or pre-soldered. The default option is for common rectangular pins included loose (the photo above shows them soldered). All pin header types use 3mm long pins. The header strips will be five pins for one side and two for the other, as seen in the photo.

Below the header option selector, you will see checkboxes for adding additional header strips (e.g. in case you want to populate all five pin pads on both sides) as well as socket strips that will mate with the Round Swiss pin header type. If you want to install the socket strips on your prototype so that you can plug in this module with Round Swiss pins, make sure to change and Update the quantity of sockets to 2 during checkout. (While a 5-pin socket is not available as a separate item, you can break off one pin from the 6-pin sockets to make them into 5-pin sockets.)

As this module only actually uses seven pins (5+2), you could save money by getting just one 8-pin strip and break it down, so those strips are listed below also.

  • Download im232P Schematic
  • Download im232P-TBP Dimensions Diagram
  • Sipex/Exar SP3232EEN Page with datasheet and other documentation



  • Available Options:
    Headers:

    Optional Recommended Products for this Item
    Rectangular Pin Header, Male, 1x40 Single Row, 2.54mm Spacing+ US$0.75
    5-pin Press-Fit Header Strip, Breakaway Pins, 2.54mm Pitch+ US$0.60
    5-pin Swiss Header, Compact, Breakaway Pins, 2.54mm Pitch+ US$0.50
    6-pin Swiss Socket, Compact, Breakaway Pins, 2.54mm Pitch+ US$0.66
    8-pin Press-Fit Header Strip, Breakaway Pins, 2.54mm Pitch+ US$0.96
    8-pin Swiss Header, Compact, Breakaway Pins, 2.54mm Pitch+ US$0.80
    8-pin Swiss Socket, Compact, Breakaway Pins, 2.54mm Pitch+ US$0.88

    This product was added to our catalog on Thursday 27 March, 2014.

    Reviews

    Customers who bought this product also purchased
    RS485 Master Interface iMOD Module, 3.3V, SP3078E, 3.5mm BlockRS485 Master Interface iMOD Module, 3.3V, SP3078E, 3.5mm BlockUS$12.95

    DIP40 to PLCC44 Adapter for PIC16/PIC18DIP40 to PLCC44 Adapter for PIC16/PIC18US$8.00

    RS485 Master 0.7" iMod, 3.3V, 3.5mm Pluggable Screw TerminalRS485 Master 0.7" iMod, 3.3V, 3.5mm Pluggable Screw TerminalUS$9.95

    PIC18F87J11 Board, iMOD ports for Ethernet, RS232 & RS485 ModulePIC18F87J11 Board, iMOD ports for Ethernet, RS232 & RS485 ModuleUS$54.95

    Ethernet-to-SPI 0.9" iMod Module, RJ45 Connector, PoE CircuitEthernet-to-SPI 0.9" iMod Module, RJ45 Connector, PoE CircuitUS$29.95

    RS232-to-TTL Breakout Board, SP3232EB (MAX3232), 3-5.5V, 10 pinsRS232-to-TTL Breakout Board, SP3232EB (MAX3232), 3-5.5V, 10 pinsUS$5.95

    Shopping Cart more
    0 items
    What's New? more
    Flowcode 7 for PIC, AVR, Arduino, ARM - Academic 50 User
    Flowcode 7 for PIC, AVR, Arduino, ARM - Academic 50 User
    US$1,727.00
    Specials more
    USB Power Regulator Board, 3.3V & 5V Ref., 0.1" Pitch (USB Reg)
    USB Power Regulator Board, 3.3V & 5V Ref., 0.1" Pitch (USB Reg)
    US$6.00
    US$4.00
    Tell A Friend
     

    Tell someone you know about this product.
    Notifications more
    NotificationsNotify me of updates to RS232 Interface 0.7" iMod Module, 3.5mm Pluggable Screw Terminal
    Reviews more
    Write ReviewWrite a review on this product!
      Friday 24 March, 2017   List of all our Products

    Copyright © 2003-2017 MicroController Pros LLC
    Powered by osCommerce