MicroController Pros Home Page My Account  Cart Contents  Checkout  
  Store » DEV-11352 My Account  |  Cart Contents  |  Checkout   
Quick Find
Enter keywords to find the product you are looking for in the Quick Find field above

or use
Advanced Search
Accessory Boards->
ADI Blackfin
Atmel AVR->
Cypress PSoC
Microchip PIC->
Silicon Labs
ST Microelectronics->
Texas Instruments->
Embedded Ethernet->
Embedded Software->
I/O Modules->
Parts & Components->
Pick & Place Tools
Programmable Logic (PLD)
Prototype PCBs->
ROM/Flash Emulators
Test & Measurement->
Tutorial Software
Universal Programmers->
Intro to Embedded Tools
Embedded News Digest
Useful Resources
Shipping & Returns
Warranty & Liability
Privacy Notice
Conditions of Use
Contact Us
Arduino 4x4 Driver Shield, 5A High-Side Chs., Chainable, DB25M US$54.95

Arduino 4x4 Driver Shield, 5A High-Side Chs., Chainable, DB25M

The 4x4 Driver Shield is designed to enable you to switch DC loads up to 5A at up to 30V with no heat-sinking. It is ideal for such applications as driving solenoids, relays, and small DC motors. It uses International Rectifier IPS6044 quad-channel fully protected high-side MOSFET switches, which include over-temp, over-current, and under-voltage protection. The high-side topology is safer in many applications than the more common low-side topology because a short to ground cannot energize the circuit while the switch is turned off. This shield also can be used to drive four unipolar stepper motors.

The board is built with generous traces to handle the current with minimal voltage loss and heating on the board. A pair of 74AHCT595 8-bit shift registers allow the control of sixteen high-current channels from only four Arduino pins using the shiftOut() function, and make it possible to daisy-chain as many as 25 boards off a single host, for a total of 400 high current channels.

4x4 Driver Shield Features

  • Arduino shield form factor compatible with all shield-compatible Arduino variants and clones
  • Sixteen 5A high-side driver channels
  • Shift register control allows daisy-chaining of up to 25 boards for a total of 400 channels
  • Uses only digital pins 7, 8, 11, and 13, leaving all serial, PWM, and analog input lines free
  • Mapped to the hardware SPI bus on the Arduino Uno, allowing high-speed data transfer
  • Inexpensive and robust DB25 male connector carries power and outputs
  • Four separate power supply circuits allow maximum application flexibility
  • Ships with loose connectors for end-user flexibility, including use with non-Arduino hosts

4x4 Driver Shield Resources

Optional Recommended Products for this Item

This product was added to our catalog on Monday 11 March, 2013.


Customers who bought this product also purchased
Arduino Stackable Female Header - 6 PinArduino Stackable Female Header - 6 PinUS$0.50

16-channel signal connector cable set, 40cm16-channel signal connector cable set, 40cmUS$10.00

Jumper Wires, M-F, 5" (Qty 10) and 40-pin HeaderJumper Wires, M-F, 5" (Qty 10) and 40-pin HeaderUS$6.00

Arduino Mega Prototyping Shield KitArduino Mega Prototyping Shield KitUS$17.95

Logic & Protocol Analyzer, 16 ch.@64kb, 100Hz-75MHz, USB PowerLogic & Protocol Analyzer, 16 ch.@64kb, 100Hz-75MHz, USB PowerUS$249.00

Arduino Stackable Female Header - 10 PinArduino Stackable Female Header - 10 PinUS$0.50

Shopping Cart more
0 items
What's New? more
Flowcode 7 for PIC, AVR, Arduino, ARM - Academic 50 User
Flowcode 7 for PIC, AVR, Arduino, ARM - Academic 50 User
Specials more
Atmel AVR STK500 Compatible Programmer, parallel port
Atmel AVR STK500 Compatible Programmer, parallel port
Tell A Friend

Tell someone you know about this product.
Notifications more
NotificationsNotify me of updates to Arduino 4x4 Driver Shield, 5A High-Side Chs., Chainable, DB25M
Reviews more
Write ReviewWrite a review on this product!
  Monday 19 March, 2018   List of all our Products

Copyright © 2003-2017 MicroController Pros LLC
Powered by osCommerce