MicroController Pros Home Page My Account  Cart Contents  Checkout  
  Store » DEV-10275 My Account  |  Cart Contents  |  Checkout   
Quick Find
 
Enter keywords to find the product you are looking for in the Quick Find field above

or use
Advanced Search
Categories
Accessory Boards->
8051->
ADI Blackfin
Arduino->
ARM->
Atmel AVR->
Cypress PSoC
Freescale->
FTDI->
Locktronics
Microchip PIC->
MIPS
Parallax->
Renesas
Silicon Labs
ST Microelectronics->
Texas Instruments->
Tibbo->
Books->
Displays->
E-Blocks->
EEPROM/EPROM/FLASH
Embedded Ethernet->
Embedded Software->
I/O Modules->
Parts & Components->
Pick & Place Tools
Programmable Logic (PLD)
Prototype PCBs->
Robotics
ROM/Flash Emulators
Test & Measurement->
Tutorial Software
Universal Programmers->
Wireless->
Information
Intro to Embedded Tools
Embedded News Digest
Useful Resources
Shipping & Returns
Warranty & Liability
Privacy Notice
Conditions of Use
Contact Us
FT232RL USB-to-Serial Board for Arduino/LilyPad, 5V, Thin PCB US$14.95

DEV-10275
FT232RL USB-to-Serial Board for Arduino/LilyPad, 5V, Thin PCB


This board functionally is the same as the FTDI Basic board, only this version has a thinner, purple PCB to match LilyPad components aesthetically.

This FT232RL USB-to-Serial Board for Arduino/LilyPad has a SMD 6-pin header on the bottom. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 5V Arduino boards. It can also be used for general serial applications. The major difference with this board is that it brings out the DTR pin as opposed to the RTS pin of the FTDI cable. The DTR pin allows an Arduino target to auto-reset when a new Sketch is downloaded. This is a really nice feature to have and allows a Sketch to be downloaded without having to hit the reset button. This board will auto-reset any Arduino board that has the reset pin brought out to a 6-pin connector. Arduino Pro and LilyPad boards use this type of connector.

The pins labeled BLK and GRN correspond to the colored wires on the FTDI cable. The black wire on the FTDI cable is GND; green is CTS. Use these BLK and GRN pins to align the FTDI basic board with your Arduino target.

This board has TX and RX LEDs that make it a bit better to use over the FTDI cable. You can actually see serial traffic on the LEDs to verify that the board is working.

A solder jumper on the back of the board allows you to configure it for 3.3V power output and I/O levels if needed.

FT232RL USB-to-Serial Board Resources


This product was added to our catalog on Wednesday 14 December, 2011.

Reviews

Shopping Cart more
0 items
What's New? more
Flowcode 7 for PIC, AVR, Arduino, ARM - Academic Single User
Flowcode 7 for PIC, AVR, Arduino, ARM - Academic Single User
US$289.00
Specials more
USB Power Regulator Board, 3.3V & 5V Ref., 0.1" Pitch (USB Reg)
USB Power Regulator Board, 3.3V & 5V Ref., 0.1" Pitch (USB Reg)
US$6.00
US$4.00
Tell A Friend
 

Tell someone you know about this product.
Notifications more
NotificationsNotify me of updates to FT232RL USB-to-Serial Board for Arduino/LilyPad, 5V, Thin PCB
Reviews more
Write ReviewWrite a review on this product!
  Tuesday 26 September, 2017   List of all our Products

Copyright © 2003-2017 MicroController Pros LLC
Powered by osCommerce