MicroController Pros Home Page
My Account  Cart Contents  Checkout  
  Store » Wireless » 434MHz & 2.4GHz » XBP24-DMWIT-250 My Account  |  Cart Contents  |  Checkout   
Quick Find
 
Enter keywords to find the product you are looking for in the Quick Find field above

or use
Advanced Search
Categories
Accessory Boards->
8051->
ADI Blackfin
Arduino->
ARM->
Atmel AVR->
Cypress PSoC
Freescale->
FTDI->
Locktronics
Microchip PIC->
MIPS
Parallax->
Renesas
Silicon Labs
ST Microelectronics->
Texas Instruments->
Tibbo->
Books->
Displays->
E-Blocks->
EEPROM/EPROM/FLASH
Embedded Ethernet->
Embedded Software->
I/O Modules->
Parts & Components->
Pick & Place Tools
Programmable Logic (PLD)
Prototype PCBs->
Robotics
ROM/Flash Emulators
Test & Measurement->
Tutorial Software
Universal Programmers->
Wireless->
  434MHz & 2.4GHz
  900MHz
  Bluetooth
  GSM/GPS->
  RFID/NFC
  WiFi->
  ZigBee
  Waspmote->
  Antennas
Information
Intro to Embedded Tools
Embedded News Digest
Useful Resources
Shipping & Returns
Warranty & Liability
Privacy Notice
Conditions of Use
Contact Us
XBee-PRO DigiMesh 2.4 RF Module, 63 mW, Wire Antenna US$38.00

XBP24-DMWIT-250
XBee-PRO DigiMesh 2.4 RF Module, 63 mW, Wire Antenna


Wireless connectivity using the DigiMesh protocol

XBee-PRO DigiMesh 2.4 delivers end-point device connectivity with a widely deployable 2.4 GHz transceiver. These modules use the innovative DigiMesh networking protocol. This innovative, peer-to-peer protocol offers users added network stability through self-healing, dense network operation and support for sleeping routers, extending the operational life of battery-dependent networks.

Part of the XBee family of wireless products, these modules are easy to use, share a common footprint, and are fully interoperable with other XBee products utilizing the same technology. This allows different XBee technologies to be drop-in replacements for each other; you can switch between 802.11, 802.15.4, ZigBee, DigiMesh and proprietary long-range with minimal development time or risk.

The XBee-PRO 2.4 DigiMesh modules use the same hardware as the XBee-PRO 802.15.4 modules. It is possible to change from one platform to the other by loading different firmware onto the same module.

Note: This module is certified for use in North America and Australia only. It is permissible to use in most of Europe if you set the PL command to 0, reducing the power output to 10 mW / 10 dBm. This module cannot be used in Japan under any circumstances; the Japanese market has a specific 10mW-max variant. See the User Manual for specific restrictions and end-product label requirements. Other areas, check local regulations.

DigiMesh Protocol

DigiMesh is a proprietary mesh networking protocol. Its features include:
  • Self-healing — Any node may enter or leave the network at any time without causing the network as a whole to fail.
  • Peer-to-peer architecture — No hierarchy and no parent-child relationships are needed.
  • Quiet protocol — Routing overhead will be reduced by using a reactive protocol similar to AODV.
  • Route discovery — Rather than maintaining a network map, routes will be discovered and created only when needed.
  • Selective acknowledgments — Only the destination node will reply to route requests.
  • Reliable delivery — Reliable delivery of data is accomplished by means of acknowledgments.
  • Sleep modes — Low-power sleep modes with synchronized wake-up are supported, with variable sleep and wake times.

2.4GHz DigiMesh Module Features

  • Power output: 63mW (+18 dBm)
  • Indoor/Urban range: Up to 300 ft (90 m)
  • Outdoor/RF line-of-sight range: Up to 1 mile (1.6 km)
  • RF data rate: 250 Kbps
  • Interface data rate: Up to 115.2 Kbps
  • Receiver sensitivity: -100 dBm
  • Spread Spectrum type: DSSS (Direct Sequence Spread Spectrum)
  • Networking topology: Mesh, point-to-point, point-to-multipoint, peer-to-peer
  • Error handling: Retries and acknowledgments
  • Channel capacity: 12 Direct Sequence Channels
  • Addressing: PAN ID, channel, and 64-bit addresses
  • Encryption: 128-bit AES
  • Supply voltage: 2.8V - 3.4V DC (Footprint Recommendation: 3.0V - 3.4V DC)
  • Transmit current: 250 mA (@ 3.3V)
  • Receive current: 55 mA (@ 3.3V)
  • Sleep current (pin sleep): <10 ľA
  • Sleep current (cyclic sleep): <50 ľA
  • Frequency band: ISM 2.4 GHz
  • Interface options: 3V CMOS Serial UART (5V-tolerant inputs)
  • Configuration method: AT and API
  • Digital I/O: 13 I/O lines
  • ADC: Six 10-bit analog inputs
  • Size: 0.960 in × 1.297 in (2.438 cm × 3.294 cm)
  • Weight: 0.10 oz (3g)
  • Operating temperature: -40°C to 85°C (industrial)
  • Certifications: FCC (USA), IC (Canada), ETSI (Europe), C-TICK (Australia)
Above specifications assume usage at full power. For Europe @ 10mW, see user manual.

Antenna options

Three other versions of this module are available:

2.4GHz DigiMesh Module Resources


This product was added to our catalog on Friday 14 October, 2011.

Reviews

Customers who bought this product also purchased
XBee-PRO DigiMesh 2.4 RF Module, 63 mW, Chip AntennaXBee-PRO DigiMesh 2.4 RF Module, 63 mW, Chip AntennaUS$38.00

XBee-PRO XSC RF 915MHz Module, 100 mW, RP-SMA ConnectorXBee-PRO XSC RF 915MHz Module, 100 mW, RP-SMA ConnectorUS$71.95

Shopping Cart more
0 items
What's New? more
Flowcode 7 "Mechatronics Pack" Feature Pack
Flowcode 7 "Mechatronics Pack" Feature Pack
US$42.00
Specials more
Arduino Duemilanove Compatible ATmega328P Board, 3.3V/5V
Arduino Duemilanove Compatible ATmega328P Board, 3.3V/5V
US$22.50
US$19.00
Tell A Friend
 

Tell someone you know about this product.
Notifications more
NotificationsNotify me of updates to XBee-PRO DigiMesh 2.4 RF Module, 63 mW, Wire Antenna
Reviews more
Write ReviewWrite a review on this product!
  Monday 27 March, 2017   List of all our Products

Copyright © 2003-2017 MicroController Pros LLC
Powered by osCommerce