MicroController Pros Home Page
My Account  Cart Contents  Checkout  
  Store » Wireless » 900MHz » XBP09-DMWIT-156 My Account  |  Cart Contents  |  Checkout   
Quick Find
 
Enter keywords to find the product you are looking for in the Quick Find field above

or use
Advanced Search
Categories
Accessory Boards->
8051->
ADI Blackfin
Arduino->
ARM->
Atmel AVR->
Cypress PSoC
Freescale->
FTDI->
Locktronics
Microchip PIC->
MIPS
Parallax->
Renesas
Silicon Labs
ST Microelectronics->
Texas Instruments->
Tibbo->
Books->
Displays->
E-Blocks->
EEPROM/EPROM/FLASH
Embedded Ethernet->
Embedded Software->
I/O Modules->
Parts & Components->
Pick & Place Tools
Programmable Logic (PLD)
Prototype PCBs->
Robotics
ROM/Flash Emulators
Test & Measurement->
Tutorial Software
Universal Programmers->
Wireless->
  434MHz & 2.4GHz
  900MHz
  Bluetooth
  GSM/GPS->
  RFID/NFC
  WiFi->
  ZigBee
  Waspmote->
  Antennas
Information
Intro to Embedded Tools
Embedded News Digest
Useful Resources
Shipping & Returns
Warranty & Liability
Privacy Notice
Conditions of Use
Contact Us
XBee-PRO DigiMesh 900 Module, 50 mW, Wire Antenna US$49.00 US$39.00

XBP09-DMWIT-156
XBee-PRO DigiMesh 900 Module, 50 mW, Wire Antenna


Long-range RF connectivity using the DigiMesh protocol

XBee-PRO DigiMesh 900 are long-range embedded wireless solutions providing end-point device connectivity. These modules use the easy-to-deploy DigiMesh networking protocol. This innovative, peer-to-peer network offers added stability through self-healing, dense network operation and support for sleeping routers, extending the operational life of battery-dependent networks. Combining the range advantages of the 900 MHz operating frequency with a fast 156 Kbps data rate to the end node and supporting RF line-of-sight ranges of up to 1.8 miles, these modules are ideal for extended-range wireless applications requiring increased data throughput.

Part of the XBee family of wireless products, these modules are easy to use, share a common footprint, and are fully interoperable with other XBee products utilizing the same technology. This allows different XBee technologies to be drop-in replacements for each other; you can switch between 802.11, 802.15.4, ZigBee, DigiMesh and proprietary long-range with minimal development time or risk.

Note: This module is certified for use in North America and Australia only. It may not be used in Europe or Japan. Other areas, check local regulations.

DigiMesh Protocol

DigiMesh is a proprietary mesh networking protocol. Its features include:
  • Self-healing — Any node may enter or leave the network at any time without causing the network as a whole to fail.
  • Peer-to-peer architecture — No hierarchy and no parent-child relationships are needed.
  • Quiet protocol — Routing overhead will be reduced by using a reactive protocol similar to AODV.
  • Route discovery — Rather than maintaining a network map, routes will be discovered and created only when needed.
  • Selective acknowledgments — Only the destination node will reply to route requests.
  • Reliable delivery — Reliable delivery of data is accomplished by means of acknowledgments.
  • Sleep modes — Low-power sleep modes with synchronized wake-up are supported, with variable sleep and wake times.

900MHz DigiMesh Module Features

  • Power output: 50mW (+17 dBm)
  • Indoor/Urban range: Up to 450 ft (140 m)
  • Outdoor/RF line-of-sight range, dipole antenna: Up to 1.8 miles (3 km)
  • RF data rate: 156 Kbps
  • Interface data rate: Up to 230 Kbps (software selectable)
  • Receiver sensitivity: -100 dBm
  • Spread Spectrum type: FHSS (Frequency Hopping Spread Spectrum)
  • Networking topology: Mesh, point-to-point, point-to-multipoint, peer-to-peer
  • Error handling: Retries and acknowledgments
  • Channel capacity: 8 hopping patterns on 12 channels, or single-channel
  • Addressing: PAN ID, channel, and 64-bit addresses
  • Encryption: 128-bit AES
  • Supply voltage: 3.0V - 3.6V DC (Footprint Recommendation: 3.0V - 3.4V DC)
  • Transmit current: 210 mA (@ 3.3V)
  • Receive current: 80 mA power-drain
  • Sleep current (asynchronous): 48 ľA typical @ 3.3V
  • Sleep current (synchronous): 60 ľA typical @ 3.3V
  • Frequency band: ISM 902 - 928 MHz
  • Interface options: 3V CMOS Serial UART (5V-tolerant inputs)
  • Configuration method: AT and API, local or over-air
  • Digital I/O: 13 I/O lines
  • ADC: Six 10-bit analog inputs
  • Size: 0.960 in × 1.297 in (2.438 cm × 3.294 cm)
  • Weight: 0.10 oz (3g)
  • Operating temperature: -40°C to 85°C (industrial)
  • Certifications: FCC (USA), IC (Canada)

Antenna options

One other version of this module is available:

900MHz DigiMesh Module Resources


This product was added to our catalog on Thursday 13 October, 2011.

Reviews

Customers who bought this product also purchased
XBee Explorer USB Dongle, USB-to-Serial Access to XBee PinsXBee Explorer USB Dongle, USB-to-Serial Access to XBee PinsUS$24.95

XBee-PRO DigiMesh 900 Module, 50 mW, RP-SMA ConnectorXBee-PRO DigiMesh 900 Module, 50 mW, RP-SMA ConnectorUS$49.00

Shopping Cart more
0 items
What's New? more
Flowcode 7 "Misc Pack A" Feature Pack
Flowcode 7 "Misc Pack A" Feature Pack
US$42.00
Specials more
USB Power Regulator Board, 3.3V & 5V Ref., 0.1" Pitch (USB Reg)
USB Power Regulator Board, 3.3V & 5V Ref., 0.1" Pitch (USB Reg)
US$6.00
US$4.00
Tell A Friend
 

Tell someone you know about this product.
Notifications more
NotificationsNotify me of updates to XBee-PRO DigiMesh 900 Module, 50 mW, Wire Antenna
Reviews more
Write ReviewWrite a review on this product!
  Wednesday 26 April, 2017   List of all our Products

Copyright © 2003-2017 MicroController Pros LLC
Powered by osCommerce