Universal Chip Programmer with 8-bit/16-bit ROM/FLASH emulator, Logic Analyzer and Pattern Generator Options
The Uprog ST is a lower-cost version of the Uprog Universal chip programmer. It features identical hardware features, but supports fewer devices (approx. 30000): View list of supported devices for this programmer.
The Uprog ST is a universal and extremely fast device programmer. It supports both in-circuit and out-of-circuit programming. Thanks to a USB 2.0 interface and specialized microprocessor, this universal chip programmer achieves short programming times that are close to the chip vendors' maximum ratings.
This unit is more than just a universal chip programmer. Through optional software licenses, the Uprog series of programmers can also be used as an 8-bit or 16-bit ROM and FLASH memory emulator, or a Logic Analyzer and Digital Pattern Generator. The programmer ships with a standard 128kBytes of internal memory, but can be upgraded to up 512kBytes (see add-on options below).
The included PC programming software supports Windows versions 2000 and higher. The software can support multiple Uprog programmers connected to a single PC.
Universal Chip Programmer w/ ROM Emulator Features USB interface — USB 2.0 (HighSpeed and FullSpeed) and USB 1.1 compatible Specialized FPGA-based microprocessor (20 ns cycle) Programming times close to chip vendors' maximum ratings In-circuit programming connector (ICP) 48-pin universal independent pin drivers which can provide VPP: 0-30V, VCC: 0.8 - 8V, CLK: ~360Hz-24MHz and GND No adapter required for any DIL devices Devices supported: EPROM, EEPROM, Flash, SPLD, CPLD, microcontrollers Adapter Creator feature allows use of programming adapters from different providers Pin contact check feature Test of digital ICs 8-bit EPROM/Flash emulator (option) 16-bit EPROM/Flash emulator (option) Ulogic: Uprog-based logic analyzer with pattern generator feature (option) Multi-color status LEDs: power, busy, error, good Banana jack on the case for grounding purpose and ESD protection Software for Windows 2000/XP/Vista/Win7 supports many independent programmers simultaneously
Sample programming times
* - Programming algorithm contains verification (P+V)
|Device ||Size ||Program ||Read, Verify|
|K9F1G08U0A ||1Gbit ||95s ||85s |
|M29W800DB ||8Mbit ||11s (P+V)* ||2s |
|AM29F040B ||4Mbit ||12s (P+V)* ||2s |
|AT25F4096 ||4Mbit ||16s ||2s |
|29DL64DF ||64Mbit ||58s (P+V)* ||8.5s |
In-Circuit Programming Connector (ICP)
The Uprog Portable Gang programmer has a built-in interface for in-circuit programming, which allows you to program chips via SPI, I2C, BDM, JTAG, 1 WIRE, 3 WIRE and other interfaces. The serial programming interface was designed to achieve maximum data speed transfers and to allow signal voltage level adjustment for any technology.
In-Circuit Programming Connection Features:
- Adjustable voltage levels (1.2V - 5V)
- Fast data transfers
- Flexible connection between programmer and programmed device
- ICP Interface supports VPP, VCC, GND, CLK, and 6 universal IO pins.
ICP also supports the pin-check feature, which monitors the signal connection to the chip to assure proper contact.
Adapter Creator Feature
Adapter Creator allows you to use many programming adapters from different providers. You can scan the pin connections of an adapter, save it to file and then use it with selected devices.
Pin Checking Feature
Uprog programmers always check if all chip pins make good contact to the programming socket before the start of programming. You can easily see if you inserted a chip incorrectly; pins which have poor contact are shown with red labels in the PC programming software. Checking for proper insertion and good pin contact virtually eliminates any incorrectly programmed or damaged chips.
Optional 8-bit EPROM Emulator Through an additional software license (see add-on options below) you can upgrade Uprog programmers to an 8-bit ROM, EPROM and FLASH memory emulator. A DIP emulation cable is included with this upgrade. Be sure to purchase the 512KB Memory Upgrade option as well if you want to emulate sizes over 128KB.
Optional 16-bit EPROM / Flash Emulator Through an additional software license (see add-on options below) you can upgrade Uprog programmers to an 16-bit ROM, EPROM and FLASH memory emulator. A DIP emulation cable is included with this upgrade. Be sure to purchase the 512KB Memory Upgrade option as well if you want to emulate sizes over 128KB.
Optional Ulogic — Digital Signal Analyzer and Pattern Generator
Through an additional software license (see add-on options below) you can upgrade Uprog programmers to a 16-channel, 200MHz Logic Analyzer and 16-channel digital pattern generator. A small adapter board that plugs into the programmer's socket and connects with 16 test probes is included with this upgrade. Combine this option with the 512KB Memory Upgrade option to increase the amount of data you can capture.
- uProg ST Programmer
- CD-ROM with software
- In-circuit programming cable
- USB cable
- Power supply
- Go to the Uprog ST Downloads Page to download the Uprog 2 software and Uprog 2 USB driver. If you purchase the optional Logic Analyzer & Pattern Generator license, you'll also need the DAQ 2 software.
Lead time: 1 week
Optional Recommended Products for this Item