MicroController Pros Home Page My Account  Cart Contents  Checkout  
  Store » Renesas » 8.06.01 My Account  |  Cart Contents  |  Checkout   
Quick Find
 
Enter keywords to find the product you are looking for in the Quick Find field above

or use
Advanced Search
Categories
Accessory Boards->
8051->
ADI Blackfin
Arduino->
ARM->
Atmel AVR->
Cypress PSoC
Freescale->
FTDI->
Locktronics
Microchip PIC->
MIPS
Parallax->
Renesas
Silicon Labs
ST Microelectronics->
Texas Instruments->
Tibbo->
Books->
Displays->
E-Blocks->
EEPROM/EPROM/FLASH
Embedded Ethernet->
Embedded Software->
I/O Modules->
Parts & Components->
Pick & Place Tools
Programmable Logic (PLD)
Prototype PCBs->
Robotics
ROM/Flash Emulators
Test & Measurement->
Tutorial Software
Universal Programmers->
Wireless->
Information
Intro to Embedded Tools
Embedded News Digest
Useful Resources
Shipping & Returns
Warranty & Liability
Privacy Notice
Conditions of Use
Contact Us
J-Link Renesas RX Adapter US$30.00

8.06.01
J-Link Renesas RX Adapter


The J-Link RX Adapter allows JTAG connections between a Segger J-Link and target hardware which comes with the Renesas RX600 series MCUs, e.g. RX610 Group, RX62N Group, RX621 Group.

All that is needed to use J-Link with a Renesas RX600 series MCU is this RX Adapter. This adapter can be used with J-Link, J-Link Pro, J-Link Ultra+, J-Link EDU and any other licensed J-Link compatible emulator. The required software can be downloaded from Segger's website and used free of charge.

J-Link with RX Adapter Features

Note: This product is the adapter only. The following feature list is meant to give you an idea of what you can do with the adapter when connected to one of the J-Link programmer/debuggers listed above.
  • Supports direct download into flash memory
  • Supports software breakpoints in flash memory (Flash breakpoints)
  • Seamless integration into the Renesas HEW & IAR Embedded Workbench IDE
  • On-chip trace support
  • Virtual UART support (C2E support)
  • All kinds of events are supported (Execution break, data access, trace break, combination/sequence of events)
  • 20-pin to standard 14-pin Renesas JTAG connector
  • USB 2.0 interface
  • JTAG speed up to 12 MHz / 25 MHz (depending on J-Link model)
  • No power supply required; powered through USB
  • All JTAG signals can be monitored, target voltage can be measured
  • Support for multiple devices
  • Fully plug-and-play compatible
  • Wide target voltage range: 1.2V - 3.3V, 5V tolerant
  • TCP/IP server included, which allows using J-Link via TCP/IP networks
  • Target power supply: J-Link can supply up to 300 mA to target with overload protection

J-Link vs. Renesas E1. What are the advantages of J-Link?

  • Higher speed
    J-Link achieves (at the time of writing, using the current versions of both the J-Link and E1 software) a speed of approximately 2-6 times the speed of the E1. This is true for basically all operations, including download to flash, setting of breakpoints in flash as well as startup and typical debugging operations like single-stepping or memory-read operations.
  • Smart breakpoint management
    Flash breakpoints are much faster on J-Link than on E1 or E20, but because of the large flash sectors of up to 128KB, setting or removing flash breakpoints is still time consuming. J-Link uses different techniques to minimize the amount of times a flash breakpoint is set or removed. Some of these techniques are: Instruction set simulation, use of hardware breakpoints where possible, dynamic conversion of breakpoint types, flash caching, CRC checking and others.
  • SDK available
    You can write your own application and control an RX600 series MCU using J-Link.
  • Same probe for ARM and RX600 CPUs
    No need to switch emulators!
  • Control panel allows monitoring of operation
  • 64-bit OS supported
  • J-Link commander: Free command-line utility for J-Link
  • J-Flash software allows using J-Link for production purposes


This product was added to our catalog on Friday 20 August, 2010.

Reviews

Customers who bought this product also purchased
J-Link 19-pin Cortex-M AdapterJ-Link 19-pin Cortex-M AdapterUS$30.00

J-Link 14-pin TI OMAP AdapterJ-Link 14-pin TI OMAP AdapterUS$60.00

20-pin to 14-pin Adapter for ARM JTAG In-Circuit Debuggers20-pin to 14-pin Adapter for ARM JTAG In-Circuit DebuggersUS$19.00

1000V DC USB Isolator1000V DC USB IsolatorUS$42.45

Shopping Cart more
0 items
What's New? more
Flowcode 7 "Test & Debugging" Feature Pack
Flowcode 7 "Test & Debugging" Feature Pack
US$54.00
Specials more
Male 5-pin, 3.81mm Terminal Block, right angle, PCB mount
Male 5-pin, 3.81mm Terminal Block, right angle, PCB mount
US$0.60
US$0.49
Tell A Friend
 

Tell someone you know about this product.
Notifications more
NotificationsNotify me of updates to J-Link Renesas RX Adapter
Reviews more
Write ReviewWrite a review on this product!
  Thursday 14 December, 2017   List of all our Products

Copyright © 2003-2017 MicroController Pros LLC
Powered by osCommerce