MicroController Pros Home Page
My Account  Cart Contents  Checkout  
  Store » Microchip PIC » Programmers » PIC-HH0110 My Account  |  Cart Contents  |  Checkout   
Quick Find
 
Enter keywords to find the product you are looking for in the Quick Find field above

or use
Advanced Search
Categories
Accessory Boards->
8051->
ADI Blackfin
Arduino->
ARM->
Atmel AVR->
Cypress PSoC
Freescale->
FTDI->
Locktronics
Microchip PIC->
  Boards->
  Books
  Chips
  In-Circuit Debuggers
  Programmers->
    ICSP Adapters
  Software
  Starter & Evaluation Kits
  Tutorials
MIPS
Parallax->
Renesas
Silicon Labs
ST Microelectronics->
Texas Instruments->
Tibbo->
Books->
Displays->
E-Blocks->
EEPROM/EPROM/FLASH
Embedded Ethernet->
Embedded Software->
I/O Modules->
Parts & Components->
Pick & Place Tools
Programmable Logic (PLD)
Prototype PCBs->
Robotics
ROM/Flash Emulators
Test & Measurement->
Tutorial Software
Universal Programmers->
Wireless->
Information
Intro to Embedded Tools
Embedded News Digest
Useful Resources
Shipping & Returns
Warranty & Liability
Privacy Notice
Conditions of Use
Contact Us
Microchip PIC Hand-Held Programmer Starter Kit with 256k, USB US$159.00

PIC-HH0110
Microchip PIC Hand-Held Programmer Starter Kit with 256k, USB


Starter Kit: Hand-Held Field and Production Programmer for Microchip PIC12F, PIC16F and PIC18F microcontrollers, plus USB PC interface and software.

The ultimate programming tool for PIC12F, PIC16F and PIC18F microcontrollers, in the field or on the production line so easy a child can use it! Just load it once and then program target devices again and again.

You need just one starter kit for your PC, then you can load as many programmers as you require.

Simply connect the starter kit dongle to your USB port and run the master software. Select your code file, device type and settings, and now you can load the programmer with your program or test code in seconds. As the programmer is battery powered during load, you don't need any power supplies or cabling; just plug a programmer into the cable supplied. Once a programmer is loaded, it is completely portable and can be used where you need it not where your PC is located.

The Handheld Programmer features one-button operation, auto sensing of target, auto verification and an error indicator. In most cases, the target circuit does not need to be powered, and low-voltage targets are supported. It can power the target circuit at 3.3V or 5V. The programmer has 256KB of memory and is powered by a common 9V PP3 battery, or by an external power supply. If your target circuit requires more than 150 mA current, it must be self-powered or the programmer must be powered by an external supply.

When it's time to program new code into your devices, simply reconnect the handheld programmer to the PC, load the new code into it, and you're ready to go again.

Hand-Held PIC Programmer Software Features

  • Supports Windows 2000/XP/Vista/7, both 32-bit and 64-bit
  • Simple software
  • Loads Flash, EEPROM, Configuration words and User ID from HEX file
  • Low or High Voltage programming
  • Select for Device ID match, configuration word verify, EEPROM Data save, and other features
  • Limit number of programs allowed, if required

Hand-Held PIC Programmer Starter Kit Contents

  • PIC Hand Held Programmer
  • PC Interface (USB) for loading code and settings
  • Ribbon cables with 10-way connector
  • 6-way flying lead adapter
  • Software CD

Hand-Held PIC Programmer Features

  • PIC Hand-held programmer uses 9V PP3 battery or power supply
  • Single-button operation
  • Reload new programs as often as you need
  • Holds program code indefinitely
  • Low or High Voltage programming
  • 10-way DIL and 6 1-way flying lead connectors included
  • Program/Verify Flash or EEPROM or both
  • Program and verify Configuration Bytes and User ID
  • Existing EEPROM Data can be preserved
  • Powers target device (up to 150mA) at 3.3V or 5V
  • For families that are low-voltage only (e.g. PIC18FxxJ and some PIC18FxxK), programmer uses 3.3V for them
  • Note: Some PIC16Fxxx devices need 4.5V minimum for chip erase, so programmer always uses 5V for these
  • Dimensions: Metric 106mm 58mm 25mm
  • Dimensions: Imperial 4.5 2.5 1 inches
  • 256kB memory

PIC Handheld Programmer Supported Devices

PIC18F microcontrollers
  • PIC18Fxxxx
  • PIC18FxxJxx
  • PIC18FxxKxx (9V VPP)
  • PIC18FxxK80, PIC18F6xK22/8xK22 and PIC18F6xK90/8xK90
  • Also supports LF versions

PIC12F microcontrollers

  • PIC12F1822, PIC12F1840
  • PIC12F609, PIC12F615
  • PIC12F635, PIC12F683
  • Also supports LF versions

PIC16F microcontrollers

  • PIC16F627
  • PIC16F628
  • PIC16F627A, PIC16F628A, PIC16F648A (HVP only if Reset pin is not reprogrammed as I/O)
  • PIC16F631, PIC16F636, PIC16F639
  • PIC16F677
  • PIC16F68x, PIC16F690
  • PIC16F7x
  • PIC16F7x7
  • PIC16F72x
  • PIC16F785
  • PIC16F818
  • PIC16F819
  • PIC16F8x
  • PIC16F8xA
  • PIC16F87x
  • PIC16F873A
  • PIC16F874A
  • PIC16F876A
  • PIC16F877A
  • PIC16F88x
  • PIC16F91x
  • PIC16F15xx
  • PIC16F193x
  • PIC16F182x
  • Note: Not all devices have LVP mode.

    Users of the old, solid yellow programmers take note: PIC16F72x, PIC16F182x and PIC16F193x need 9V VPP. The old solid yellow programmers (i.e. PIC-HH0010 / PIC-HH0020) only could supply 12.5V VPP, thus can not be used to program those devices. You must have the current yellow & black programmer (i.e. PIC-HH0110 / PIC-HH0120) to program them.

Not supported

  • PIC16F630
  • PIC16F676
  • PIC16F505
  • PIC16F5x will be supported in a future update
Free updates are available for new device support. This list is current as of 4 January 2013.

Extra PIC Hand-Held Programmers are available individually. You only need one starter kit for as many programmers as you require.

Power Supply

If you do not want to use the internal 9V PP3 battery, the power supply required is 9V with a 5.0/2.1mm Barrel connector. See below for optional universal power supplies that can be used in most countries.

Designing the Handheld Programmer into Your Product

To use a handheld programmer to configure your product in the field or on the production line, you need to have a 10-way box connector or just use the 6-way flying lead adapter.

The header has 0.1-inch (2.54mm) pin spacing. The GND pins marked with an asterisk (*) must be connected to target ground. Either or both of the other GND pins also must be connected to target ground. VDD must be connected to the target circuit's Vdd. The PGM pin is only used for LVP mode.

For more information, see the PIC 256k Handheld Programmer Quick Start Guide.


Optional Recommended Products for this Item
Power Supply 3-12V DC, U.S. plug, 6 connection tips+ US$11.00
Power Supply 3-12V DC, US/UK/Euro/AU Plugs, 100-240VAC+ US$13.00

This product was added to our catalog on Friday 16 October, 2009.

Reviews

Customers who bought this product also purchased
40-pin ZIF socket for 0.3" and 0.6" wide DIP packages40-pin ZIF socket for 0.3" and 0.6" wide DIP packagesUS$11.00

FlowKit: Real-time Debugging System for FlowcodeFlowKit: Real-time Debugging System for FlowcodeUS$135.83

Microchip PIC Hand-Held 8-Way Programmer Starter Kit with 2MBMicrochip PIC Hand-Held 8-Way Programmer Starter Kit with 2MBUS$189.00

Microchip PIC Hand-Held Programmer, 256k, Extra UnitMicrochip PIC Hand-Held Programmer, 256k, Extra UnitUS$139.00

Power Supply 3-12V DC, U.S. plug, 6 connection tipsPower Supply 3-12V DC, U.S. plug, 6 connection tipsUS$11.00

Shopping Cart more
0 items
What's New? more
Flowcode 7 "Mechatronics Pack" Feature Pack
Flowcode 7 "Mechatronics Pack" Feature Pack
US$42.00
Specials more
Arduino Duemilanove Compatible ATmega328P Board, 3.3V/5V
Arduino Duemilanove Compatible ATmega328P Board, 3.3V/5V
US$22.50
US$19.00
Tell A Friend
 

Tell someone you know about this product.
Notifications more
NotificationsNotify me of updates to Microchip PIC Hand-Held Programmer Starter Kit with 256k, USB
Reviews more
Write ReviewWrite a review on this product!
  Thursday 20 July, 2017   List of all our Products

Copyright © 2003-2017 MicroController Pros LLC
Powered by osCommerce