MicroController Pros Home Page My Account  Cart Contents  Checkout  
  Store » Wireless » ZigBee » XBP24BZ7WIT-004 My Account  |  Cart Contents  |  Checkout   
Quick Find
Enter keywords to find the product you are looking for in the Quick Find field above

or use
Advanced Search
Accessory Boards->
ADI Blackfin
Atmel AVR->
Cypress PSoC
Microchip PIC->
Silicon Labs
ST Microelectronics->
Texas Instruments->
Embedded Ethernet->
Embedded Software->
I/O Modules->
Parts & Components->
Pick & Place Tools
Programmable Logic (PLD)
Prototype PCBs->
ROM/Flash Emulators
Test & Measurement->
Tutorial Software
Universal Programmers->
  434MHz & 2.4GHz
Intro to Embedded Tools
Embedded News Digest
Useful Resources
Shipping & Returns
Warranty & Liability
Privacy Notice
Conditions of Use
Contact Us
XBee-PRO ZB S2B ZigBee Module, 63 mW, Wire Antenna US$34.00

XBee-PRO ZB S2B ZigBee Module, 63 mW, Wire Antenna

Wireless connectivity using the ZigBee protocol

XBee-PRO ZB S2B embedded RF modules provide cost-effective wireless connectivity to devices in ZigBee mesh networks. Utilizing the ZigBee PRO Feature Set, these modules are interoperable with other ZigBee devices, including devices from other vendors.

Part of the XBee family of wireless products, these modules are easy to use, share a common footprint, and are fully interoperable with other XBee products utilizing the same technology. This allows different XBee technologies to be drop-in replacements for each other; you can switch between 802.11, 802.15.4, ZigBee, DigiMesh and proprietary long-range with minimal development time or risk.

Series 2 modules use a different hardware configuration from the earlier models. They are not compatible with the outdated ZNet Series 2.5 modules.

ZB Series 2 New Features

ZB offers many new and improved features over ZNet 2.5, including:
  • Data transmissions are resolved directly to APS unicasts. This provides the ability to send and receive ZDO commands.
  • NH command configures the unicast transmission timeout. This command can extend the number of unicast hops dramatically beyond the 6-8 hop limit that existed in ZNet 2.5.
  • ZS command allows ZigBee stack profile to be set as required.
  • Routers and coordinators can expire end-device children from their child tables if the end device has not polled within a settable timeout.
  • The ZA command is no longer needed. SE, DE and CI addressing commands are always enabled.
  • AI now includes several new values.

Note: This module is certified for use in North America and Australia only. It is permissible to use in most of Europe if you set the PL command to 0, reducing the power output to 10 mW / 10 dBm. This module cannot be used in Japan under any circumstances; the Japanese market has a specific 10mW-max variant. See the User Manual for specific restrictions and end-product label requirements. Other areas, check local regulations.

ZB S2B ZigBee Module Features

  • Power output: 63mW (+18 dBm)
  • Indoor/Urban range: Up to 300 ft (90 m)
  • Outdoor/RF line-of-sight range: Up to 2 miles (3200 m)
  • RF data rate: 250 Kbps
  • Interface data rate: 1200 bps to 1 Mbps (non-standard baud rates supported)
  • Receiver sensitivity: -102 dBm
  • Spread Spectrum type: DSSS (Direct Sequence Spread Spectrum)
  • Networking topology: Mesh, point-to-point, point-to-multipoint, peer-to-peer
  • Error handling: Retries and acknowledgments
  • Channel capacity: 15 Direct Sequence Channels (11 through 25)
  • Addressing: PAN ID, 64-bit IEEE MAC
  • Encryption: 128-bit AES
  • Supply voltage: 2.7V - 3.6V DC (Footprint Recommendation: 3.0V - 3.4V DC)
  • Transmit current: 205 mA (@ 3.3V)
  • Receive current: 47 mA (@ 3.3V)
  • Idle current: 15 mA
  • Sleep current: 3.5 A typical @ 25C
  • Frequency band: ISM 2.4 GHz
  • Interface options: 3V CMOS UART, ADC, DIO
  • Configuration method: AT and API, local or over-air
  • Digital I/O: 10 I/O lines
  • ADC: Four 10-bit analog inputs
  • Size: 0.960 in 1.297 in (2.438 cm 3.294 cm)
  • Weight: 0.10 oz (3g)
  • Operating temperature: -40C to 85C (industrial)
  • Certifications: FCC (USA), IC (Canada), ETSI (Europe), C-TICK (Australia)

Antenna options

Three other versions of this module are available:

ZB S2B ZigBee Module Resources

This product was added to our catalog on Friday 17 July, 2009.


Customers who bought this product also purchased
XBee-PRO DigiMesh 2.4 RF Module, 63 mW, RP-SMA ConnectorXBee-PRO DigiMesh 2.4 RF Module, 63 mW, RP-SMA ConnectorUS$44.00

USB 2.0 Extension Cable, 6 feetUSB 2.0 Extension Cable, 6 feetUS$3.95

Jumper Wires, F-F, 3" (Qty 10) and 40-pin HeaderJumper Wires, F-F, 3" (Qty 10) and 40-pin HeaderUS$6.00

Pack of 12 Prototyping Wires for 0.025-inch Square PinsPack of 12 Prototyping Wires for 0.025-inch Square PinsUS$6.90

XBee Explorer Serial, RS232-to-Serial Access to XBee PinsXBee Explorer Serial, RS232-to-Serial Access to XBee PinsUS$29.95

Power Supply 3-12V DC, US/UK/Euro/AU Plugs, 100-240VACPower Supply 3-12V DC, US/UK/Euro/AU Plugs, 100-240VACUS$13.00

Shopping Cart more
0 items
What's New? more
Flowcode 7 for PIC, AVR, Arduino, ARM - Pro 2 User
Flowcode 7 for PIC, AVR, Arduino, ARM - Pro 2 User
Specials more
Male 5-pin, 3.81mm Terminal Block, right angle, PCB mount
Male 5-pin, 3.81mm Terminal Block, right angle, PCB mount
Tell A Friend

Tell someone you know about this product.
Notifications more
NotificationsNotify me of updates to XBee-PRO ZB S2B ZigBee Module, 63 mW, Wire Antenna
Reviews more
Write ReviewWrite a review on this product!
  Wednesday 14 November, 2018   List of all our Products

Copyright © 2003-2017 MicroController Pros LLC
Powered by osCommerce