MicroController Pros Home Page
My Account  Cart Contents  Checkout  
  Store » Microchip PIC » Programmers » ICSP Adapters » PIC-ICSP My Account  |  Cart Contents  |  Checkout   
Quick Find
 
Enter keywords to find the product you are looking for in the Quick Find field above

or use
Advanced Search
Categories
Accessory Boards->
8051->
ADI Blackfin
Arduino->
ARM->
Atmel AVR->
Cypress PSoC
Freescale->
FTDI->
Locktronics
Microchip PIC->
  Boards->
  Books
  Chips
  In-Circuit Debuggers
  Programmers->
    ICSP Adapters
  Software
  Starter & Evaluation Kits
  Tutorials
MIPS
Parallax->
Renesas
Silicon Labs
ST Microelectronics->
Texas Instruments->
Tibbo->
Books->
Displays->
E-Blocks->
EEPROM/EPROM/FLASH
Embedded Ethernet->
Embedded Software->
I/O Modules->
Parts & Components->
Pick & Place Tools
Programmable Logic (PLD)
Prototype PCBs->
Robotics
ROM/Flash Emulators
Test & Measurement->
Tutorial CD-ROMs
Universal Programmers->
Wireless->
Information
Intro to Embedded Tools
Embedded News Digest
Useful Resources
Shipping & Returns
Warranty & Liability
Privacy Notice
Conditions of Use
Contact Us
PIC ICSP Adapter, 6-pin Single Row to RJ12 and 2mm 2x4 Header US$9.50

PIC-ICSP
PIC ICSP Adapter, 6-pin Single Row to RJ12 and 2mm 2x4 Header


In-System Programming Adapter for connecting between PIC target boards and PIC In-Circuit Debuggers & Programmers with the following ICSP (in-circuit serial programming) connectors: RJ12 jack; Single row male headers; 2 row x 4 pin, 2.00mm male headers

This PIC ICSP Adapter is also a fully functional replacement (and more) for the Modtronix PGM06 programming adapter. It can be used to connect all Modtronix SBC boards to any PIC programmer/debugger that uses a RJ12 or a single row, 0.1" spaced programming connector.

Connect from RJ12 ICSP jack PIC In-Circuit Debuggers/Programmers (MPLAB-ICD2, MachX, ICD-X, ICDX-30U) to:

  • 2.0mm 2x4 male ICSP header found on Modtronix SBC series boards
  • Any target board with 0.1" spaced, male, square post ICSP headers (Olimex boards, DHMicro boards)

The image below shows a Modtronix SBC65EC board connected to the Mach X In-Circuit debugger/Programmer using this PIC ICSP Adapter.

Connect from 0.1"-spaced, male single-row ICSP header PIC In-Circuit Debuggers/Programmers (Olimex PIC-ICD2, PIC-MCP-USB, PRESTO, PIC-K149B) to:

  • 2.0mm 2x4 male ICSP header found on Modtronix SBC series boards
  • Any target board with RJ12 ICSP headers (Microchip boards, CCS boards), using the included RJ12 cable

The image below shows an Modtronix SBC65EC board connected to the Olimex PIC-ICD2 In-Circuit debugger/Programmer using this PIC ICSP Adapter.

This adapter consists of a small PCB with RJ12 jack and 6-pin single-row male 0.1" spacing connector on top, and a 2.0mm 2x4 female connector on the bottom. The 2mm connector plugs directly onto the ICSP connector of Modtronix SBC series boards.

Included with the adapter are six single wires with square female crimp connectors on each end that fit onto standard square pin headers. These wires allow you to connect from the adapter's 6-pin single-row header to any target board and/or programmer with 0.1"-spaced square pin headers, thus allowing you to use such boards with programmers/debuggers that have an RJ12 connector.

Also included is a 20cm cable with RJ12 connectors on each end. Note that the RJ12 connector pins on PIC target boards are mirrored from the pinout on PIC programmers and in-circuit debuggers with RJ12 connector (like the Microchip MPLAB-ICD2). Therefore, the included cable has been reverse-wired to allow you to connect from the adapter's 6-pin single-row ICSP connector to targets with RJ12 connector. You would use the included cable for example to connect an Olimex PIC-ICD2 with 6-pin single-row connector to a target board that has a RJ12 connector.

To connect from a debugger/programmer with RJ12 connector to a target with single-row connector, however, you would use the RJ12 cable that came with your debugger/programmer (straight-through cable) the included reverse-wired cable will not work in that direction.

The adapter's 6-contact RJ12 socket accepts the RJ12 cable supplied with Microchip's MPLAB-ICD2 Debugger/Programmer and other ICD devices that are pinout compatible with Microchip's RJ12 connector, like the CCS ICD, MachX In-Circuit Debugger/Programmer, or ICDX-30U In-Circuit Debugger/Programmer

Supported PIC Target Boards with 2.0mm ICSP connector

Ships from: USA
Leadtime: in stock


This product was added to our catalog on Tuesday 23 October, 2007.

Reviews

Customers who bought this product also purchased
PIC Development Module for 8- to 28-pin SOIC @ 1.27mm pitchPIC Development Module for 8- to 28-pin SOIC @ 1.27mm pitchUS$15.00

Friction Lock Header, 6-pin, 0.1" male straight (10-pack)Friction Lock Header, 6-pin, 0.1" male straight (10-pack)US$1.40

Prototype Daughter Board for SBC83IPrototype Daughter Board for SBC83IUS$4.95

PIC18F26J50 Prototype Board, 8x LEDs, USB, ICSP, UEXTPIC18F26J50 Prototype Board, 8x LEDs, USB, ICSP, UEXTUS$12.80

Prototyping Board in mikroBUS Form Factor (PROTO click)Prototyping Board in mikroBUS Form Factor (PROTO click)US$4.50

Arduino Adapter Shield for 4D Systems LCD/OLED DisplaysArduino Adapter Shield for 4D Systems LCD/OLED DisplaysUS$7.71

Shopping Cart more
0 items
What's New? more
10-inch LCD Touchscreen for OLinuXino and LIME/LIME2, 1024x600
10-inch LCD Touchscreen for OLinuXino and LIME/LIME2, 1024x600
US$106.56
Specials more
Arduino Duemilanove Compatible ATmega328P Board, 3.3V/5V
Arduino Duemilanove Compatible ATmega328P Board, 3.3V/5V
US$22.50
US$19.00
Tell A Friend
 

Tell someone you know about this product.
Notifications more
NotificationsNotify me of updates to PIC ICSP Adapter, 6-pin Single Row to RJ12 and 2mm 2x4 Header
Reviews more
Write ReviewWrite a review on this product!
  Tuesday 25 November, 2014   List of all our Products

Copyright © 2003-2014 MicroController Pros LLC
Powered by osCommerce