MicroController Pros Home Page
My Account  Cart Contents  Checkout  
  Store » Microchip PIC » Programmers » PIC-MCP-USB My Account  |  Cart Contents  |  Checkout   
Quick Find
 
Enter keywords to find the product you are looking for in the Quick Find field above

or use
Advanced Search
Categories
Accessory Boards->
8051->
ADI Blackfin
Arduino->
ARM->
Atmel AVR->
Cypress PSoC
Freescale->
FTDI->
Locktronics
Microchip PIC->
  Boards->
  Books
  Chips
  In-Circuit Debuggers
  Programmers->
    ICSP Adapters
  Software
  Starter & Evaluation Kits
  Tutorials
MIPS
Parallax->
Renesas
Silicon Labs
ST Microelectronics->
Texas Instruments->
Tibbo->
Books->
Displays->
E-Blocks->
EEPROM/EPROM/FLASH
Embedded Ethernet->
Embedded Software->
I/O Modules->
Parts & Components->
Pick & Place Tools
Programmable Logic (PLD)
Prototype PCBs->
Robotics
ROM/Flash Emulators
Test & Measurement->
Tutorial Software
Universal Programmers->
Wireless->
Information
Intro to Embedded Tools
Embedded News Digest
Useful Resources
Shipping & Returns
Warranty & Liability
Privacy Notice
Conditions of Use
Contact Us
Microchip PIC Programmer, PICSTART Plus compatible, USB US$48.26

PIC-MCP-USB
Microchip PIC Programmer, PICSTART Plus compatible, USB


Low-cost PIC programmer with USB port

This PIC Programmer is both an out-of-circuit and in-circuit programmer for all Microchip PIC devices that are supported by Microchip's own free MPLAB software, with the exception of PIC17xxx. It performs blank check, read, program, and verify.

The USB driver for this programmer will install a virtual serial (COM) port on your PC. The MPLAB software will think it is talking to Microchip's serial-port PICSTART Plus programmer. PIC-MCP-USB is compatible with MPLAB v7.52 through v8.92. Like the PICSTART Plus, it is not compatible with MPLAB X.

This programmer uses an FT232BM chip to handle the USB virtual COM port. The USB driver is not shipped with this programmer; download the drivers for Windows (tested with 2000, XP, and Windows 7 both 32- and 64-bit). Do not use drivers newer than version 2.04.06!

Firmware upgrading is accomplished through the USB port with a simple update program run on your PC. Just download the firmware update (version 1.30), connect the PIC-MCP-USB to your USB port and wait for the Virtual COM port to be set up, then run the PIC-MCP-upgrade.exe update application and direct it to the Virtual COM port. When it reports a successful upgrade, unplug the PIC-MCP-USB, wait for Windows to unload the Virtual COM port, then plug it back in. You should not ever need to upgrade the firmware, however.

In standalone mode, a gold-plated ZIF socket is used to program 8-, 18-, 28- and 40-pin PICs in DIP form. By setting a jumper, the PIC-MCP-USB becomes an in-circuit programmer using a 0.1"-spaced six-pin ICSP connector.

The PIC-MCP-USB measures 100 80 mm (3.9 3.15"). It comes fully assembled and tested. It does not ship with any documentation or software.

What to do if you accidentally install newer FTDI drivers

FTDI drivers beyond version 2.04.06 do not work with this programmer. If you have installed newer drivers, you will continually get a message that the firmware needs to be updated, and the programmer will be unusable. Follow these steps to uninstall the newer drivers and get your programmer working again:

First, download the FTClean utility and unzip it. Run the FTClean.exe and leave FTDI set to "VID(hix)" but enter 6001 in the PID field. Then click the "Clean System" button, disconnect the PIC-MCP-USB from the computer, and agree to the uninstallation. Wait for a few seconds until the cleaning process is complete.

Then, before you plug the PIC-MCP-USB back into the computer, make sure you have disabled the driver auto-search (auto-update) in Windows if your version of Windows has such a feature. Plug in the device and manually point the hardware driver installation wizard to the folder where you have unzipped the V2.04.06 drivers. If there is a warning message when the PIC-MCP-USB is enabled, just ignore it.

Ships from: USA
Leadtime: In stock


Optional Recommended Products for this Item
USB 2.0 Cable, 6ft., A-Male / B-Male+ US$6.00
Cable 2x 6-pin single row, female connector, 2.5mm (Olimex ICSP)+ US$4.90
PIC ICSP Adapter, 6-pin Single Row to RJ12 and 2mm 2x4 Header+ US$9.50
1000V DC USB Isolator+ US$41.33

This product was added to our catalog on Tuesday 07 March, 2006.

Reviews

Customers who bought this product also purchased
ENC28J60 Ethernet Interface to SPI Header BoardENC28J60 Ethernet Interface to SPI Header BoardUS$19.22

Microchip PICkit3 Compatible In-Circuit Programmer/Debugger, USBMicrochip PICkit3 Compatible In-Circuit Programmer/Debugger, USBUS$41.33

USB Adapter, A-Male to B-FemaleUSB Adapter, A-Male to B-FemaleUS$2.50

Plastic Pen Stylus for Touch ScreensPlastic Pen Stylus for Touch ScreensUS$2.00

EasyDriver Stepper Motor Driver, v4.4EasyDriver Stepper Motor Driver, v4.4US$14.95

Bipolar Stepper Motor Driver Board, A3967SLB, IDC10 InterfaceBipolar Stepper Motor Driver Board, A3967SLB, IDC10 InterfaceUS$24.00

Shopping Cart more
0 items
What's New? more
J-Link ULTRA+, High-Speed USB JTAG Debugger with Software
J-Link ULTRA+, High-Speed USB JTAG Debugger with Software
US$748.00
Specials more
Arduino Duemilanove Compatible ATmega328P Board, 3.3V/5V
Arduino Duemilanove Compatible ATmega328P Board, 3.3V/5V
US$22.50
US$19.00
Tell A Friend
 

Tell someone you know about this product.
Notifications more
NotificationsNotify me of updates to Microchip PIC Programmer, PICSTART Plus compatible, USB
Reviews more
Write ReviewWrite a review on this product!
  Wednesday 28 June, 2017   List of all our Products

Copyright © 2003-2017 MicroController Pros LLC
Powered by osCommerce