MicroController Pros Home Page My Account  Cart Contents  Checkout  
  Store » Parts & Components » Joysticks/Keypads » SEN-12041 My Account  |  Cart Contents  |  Checkout   
Quick Find
 
Enter keywords to find the product you are looking for in the Quick Find field above

or use
Advanced Search
Categories
Accessory Boards->
8051->
ADI Blackfin
Arduino->
ARM->
Atmel AVR->
Cypress PSoC
Freescale->
FTDI->
Locktronics
Microchip PIC->
MIPS
Parallax->
Renesas
Silicon Labs
ST Microelectronics->
Texas Instruments->
Tibbo->
Books->
Displays->
E-Blocks->
EEPROM/EPROM/FLASH
Embedded Ethernet->
Embedded Software->
I/O Modules->
Parts & Components->
  Batteries & Chargers
  Buzzers
  Cables/Adapters->
  Cameras
  Chips/ICs
  Connectors
  Crystals
  Diodes
  IC Sockets
  Joysticks/Keypads
  LEDs
  Memory Cards
  Motor Drivers
  Power Supplies/Adapters
  Relays
  Resistors
  RTCs
  Sensors->
  Solar Cells
  Switches
  Transistors
  Voltage Regulators
  Generic Pin Converters
Pick & Place Tools
Programmable Logic (PLD)
Prototype PCBs->
Robotics
ROM/Flash Emulators
Test & Measurement->
Tutorial Software
Universal Programmers->
Wireless->
Information
Intro to Embedded Tools
Embedded News Digest
Useful Resources
Shipping & Returns
Warranty & Liability
Privacy Notice
Conditions of Use
Contact Us
Capacitive Touch Sensor Board, AT42QT1010, 1.8V-5V, 1 Pad US$7.95

SEN-12041
Capacitive Touch Sensor Board, AT42QT1010, 1.8V-5V, 1 Pad


The AT42QT1010 Capacitive Touch Breakout offers a single capacitive touch button with easy-to-use digital I/O pins. The Atmel AT42QT1010 Charge-Transfer (QT) Sensor is a dedicated, single-button capacitive sense chip. The chip handles monitoring a conductive area for touch. As long as a touch (e.g. from a finger) is detected, the AT42QT1010 keeps the output line high. Otherwise, the line is kept low. It doesn't even have to be a direct touch; it can sense a finger near it you can even cover the "button" part of this board with a plastic layer and it still will work.

You just need to provide a power source (1.8V to 5V) and Ground for the AT42QT1010 to function. Additionally, a PAD pin is available if you would like to create your own external electrode. The on-board electrode (touch area) is on the opposite side from what's shown in the picture. You can use surface-mount pin headers placed on the solder pads for a totally flush "button" side, or through-hole pin headers.

The output from the AT42QT1010 goes directly to the OUT pin on the board as well as to the transistor on the left side which operates the LED in the center of board. By default, the OUT line and LED lines are connected, which means that on a touch, the on-board LED lights up. You can disconnect the LED by de-soldering the jumper labeled LED Enable. This will stop the LED lighting up when there is a touch, but you can still drive the LED externally using the LED pin on the board.

Two Operating Modes Available

On the right side of the board, there is a solder jumper labeled Mode with L and F markers. By default, the center pad and the F pad are connected, which puts the AT42QT1010 in Fast mode. In Fast mode, the chip is more responsive to touch events but draws 200A to 750A in normal operation. If you de-solder this jumper and connect the center pad to the L pad, the AT42QT1010 will be in Low-Power mode. In this mode, the chip is slightly less responsive to events but uses only 15A to 75A.

Example Usages

Here, you can see the sensor working through a 0.125-inch acrylic cover (the LED is on, indicating a touch):

Here, you see how some strips of copper have been used as an external electrode:

Capacitive Touch Module Board Resources


Optional Recommended Products for this Item
Rectangular Pin Header, Male, 1x40 Single Row, 2.54mm Spacing+ US$0.75
40-pin Single Row Right-Angle Headers, 0.1" Pitch, 10 pieces+ US$6.00

This product was added to our catalog on Friday 11 April, 2014.

Reviews

Shopping Cart more
0 items
What's New? more
J-Link ULTRA+, High-Speed USB JTAG Debugger with Software
J-Link ULTRA+, High-Speed USB JTAG Debugger with Software
US$748.00
Specials more
4-port USB2.0 Hub, Unpowered, ASUS Zenhub
4-port USB2.0 Hub, Unpowered, ASUS Zenhub
US$10.00
US$5.90
Tell A Friend
 

Tell someone you know about this product.
Notifications more
NotificationsNotify me of updates to Capacitive Touch Sensor Board, AT42QT1010, 1.8V-5V, 1 Pad
Reviews more
Write ReviewWrite a review on this product!
  Tuesday 21 November, 2017   List of all our Products

Copyright © 2003-2017 MicroController Pros LLC
Powered by osCommerce