MicroController Pros Home Page My Account  Cart Contents  Checkout  
  Store » Parts & Components » Joysticks/Keypads » COM-13169 My Account  |  Cart Contents  |  Checkout   
Quick Find
 
Enter keywords to find the product you are looking for in the Quick Find field above

or use
Advanced Search
Categories
Accessory Boards->
8051->
ADI Blackfin
Arduino->
ARM->
Atmel AVR->
Cypress PSoC
Freescale->
FTDI->
Locktronics
Microchip PIC->
MIPS
Parallax->
Renesas
Silicon Labs
ST Microelectronics->
Texas Instruments->
Tibbo->
Books->
Displays->
E-Blocks->
EEPROM/EPROM/FLASH
Embedded Ethernet->
Embedded Software->
I/O Modules->
Parts & Components->
  Batteries & Chargers
  Buzzers
  Cables/Adapters->
  Cameras
  Chips/ICs
  Connectors
  Crystals
  Diodes
  IC Sockets
  Joysticks/Keypads
  LEDs
  Memory Cards
  Motor Drivers
  Power Supplies/Adapters
  Relays
  Resistors
  RTCs
  Sensors->
  Solar Cells
  Switches
  Transistors
  Voltage Regulators
  Generic Pin Converters
Pick & Place Tools
Programmable Logic (PLD)
Prototype PCBs->
Robotics
ROM/Flash Emulators
Test & Measurement->
Tutorial Software
Universal Programmers->
Wireless->
Information
Intro to Embedded Tools
Embedded News Digest
Useful Resources
Shipping & Returns
Warranty & Liability
Privacy Notice
Conditions of Use
Contact Us
Trackball Board, Lighted Ball with Pushbutton US$24.95

COM-13169
Trackball Board, Lighted Ball with Pushbutton


This board allows you to add a lighted trackball input device to your project. The trackball is the type found on many Blackberry models. The four spindles on the trackball have a tiny circular magnet the end. Each of these is paired with an SMD Hall-effect sensor. These sensors are used to measure up, down, left and right movements of the trackball. An SMD momentary switch is placed under the trackball to give you a select switch. The BTN line will be pulled low when the switch is pressed.

Also included on the Trackballer are four LEDs: red, blue, green and white. These can be powered to light the clear trackball any color. The lower picture shows the trackball unit in use with the white LED lighted.

All features are broken out to a 0.1"-pitch header. Regulated 2.5V to 5.25V DC power must be provided to power the Hall sensors. The trackball is attached with CA glue then held in place with the upper mounting PCB as shown. You can remove the mounting board if you wish; the Phillips screws and nylon standoffs are standard 4-40 size. The board comes as shown in the upper picture, with all components populated and the mounting PCB already assembled. Header pins are not included; you can add some using the option selector below.

If you do replace the mounting PCB with your own enclosure, note that overtightening the mounting screws can cause the Hall-effect sensors to malfunction.

The Hall-effect sensors and trackball combo are surprisingly sensitive. A slight roll of the trackball creates multiple high/low transitions on the four axis pins, easily picked up by any microcontroller. A 360 rotation of the trackball along a single axis will result in about nine high/low transitions.

Trackball Breakout Board Features

  • Translucent select button
  • 360 direction
  • Hall-effect sensors measure up/down/left/right movements of trackball
  • Red, blue, green, white LEDs to light up the trackball
  • Mounting PCB to mechanically stabilize the trackball
  • All pins broken out to 0.1"-pitch header
  • Dimensions: 1.12 0.97 0.7 inches (28.5 24.8 18 mm)

Trackball Breakout Board Resources

Note that the Jumper Wire pack in the options below contains 10 wires, but this board will require 11 wires. We have many different packs of M-F Jumper Wires available, as well as F-F and even M-M if your configuration will require that.


Optional Recommended Products for this Item
Rectangular Pin Header, Male, 1x40 Single Row, 2.54mm Spacing+ US$0.75
40-pin Single Row Right-Angle Headers, 0.1" Pitch, 10 pieces+ US$6.00
Jumper Wires, M-F, 5" (Qty 10) and 40-pin Header+ US$6.00

This product was added to our catalog on Thursday 15 December, 2011.

Reviews

Customers who bought this product also purchased
5-Position Switch, 18 Input States, 8-pin DIP5-Position Switch, 18 Input States, 8-pin DIPUS$9.99

Digital/Analog I/O Interface Board, Buttons, Sensors, Pots, LEDsDigital/Analog I/O Interface Board, Buttons, Sensors, Pots, LEDsUS$12.00

2x5 (10-pin) 0.05" pitch IDC Connector Flat Ribbon Cable, 20cm2x5 (10-pin) 0.05" pitch IDC Connector Flat Ribbon Cable, 20cmUS$2.60

Atmel AVR ISP Adapter, 10-pin to 6-pin (Atmel Butterfly)Atmel AVR ISP Adapter, 10-pin to 6-pin (Atmel Butterfly)US$7.50

Electret Microphone Board with OPA344 Operational AmplifierElectret Microphone Board with OPA344 Operational AmplifierUS$7.95

Ambient Light Sensor Board, TEMT6000X01Ambient Light Sensor Board, TEMT6000X01US$4.95

Shopping Cart more
0 items
What's New? more
Flowcode 7 for PIC, AVR, Arduino, ARM - Academic Single User
Flowcode 7 for PIC, AVR, Arduino, ARM - Academic Single User
US$289.00
Specials more
2N3906 PNP Transistor, 200mA/40V, TO-92 (10 pack)
2N3906 PNP Transistor, 200mA/40V, TO-92 (10 pack)
US$1.10
US$0.59
Tell A Friend
 

Tell someone you know about this product.
Notifications more
NotificationsNotify me of updates to Trackball Board, Lighted Ball with Pushbutton
Reviews more
Write ReviewWrite a review on this product!
  Saturday 16 December, 2017   List of all our Products

Copyright © 2003-2017 MicroController Pros LLC
Powered by osCommerce