MicroController Pros Home Page
My Account  Cart Contents  Checkout  
  Store » EM-P-NXP My Account  |  Cart Contents  |  Checkout   
Quick Find
 
Enter keywords to find the product you are looking for in the Quick Find field above

or use
Advanced Search
Categories
Accessory Boards->
8051->
ADI Blackfin
Arduino->
ARM->
Atmel AVR->
Cypress PSoC
Freescale->
FTDI->
Locktronics
Microchip PIC->
MIPS
Parallax->
Renesas
Silicon Labs
ST Microelectronics->
Texas Instruments->
Tibbo->
Books->
Displays->
E-Blocks->
EEPROM/EPROM/FLASH
Embedded Ethernet->
Embedded Software->
I/O Modules->
Parts & Components->
Pick & Place Tools
Programmable Logic (PLD)
Prototype PCBs->
Robotics
ROM/Flash Emulators
Test & Measurement->
Tutorial CD-ROMs
Universal Programmers->
Wireless->
Information
Intro to Embedded Tools
Embedded News Digest
Useful Resources
Shipping & Returns
Warranty & Liability
Privacy Notice
Conditions of Use
Contact Us
USB Programmer for NXP LPC and P89V51 Microcontrollers US$20.00

EM-P-NXP
USB Programmer for NXP LPC and P89V51 Microcontrollers


Simple and low cost USB programmer for NXP LPC series ARM processors and P89V51 series controllers.

This little USB programmer for LPC and P89Vxx micros works with the free FlashMagic programming software utility and allows you to program the micro's internal Flash via your PC's USB port.

NXP ARM-core based LPC series microcontrollers and 8051-core based P89Vxx microcontrollers ship from the factory with an integrated bootloader that allows programming of the chip's internal Flash memory via the chip's integrated UART serial interface using the free FlashMagic programming software utility.

Traditionally the connection from the microcontroller's UART to a PC required a RS232 transceiver on the target board and a physical RS232 serial port on the PC side for this type of programming. As more and more PCs ship without RS232 port, a new solution is required: Meet our new USB-to-Serial programmer specifically designed for this task. This low cost programmer for LPC and P89V51 series microcontrollers plugs into a PC's USB port. The USB driver installs a virtual COM port on your PC, so the device looks to the FlashMagic software like a physical RS232 port. The programmer's FTDI USB-to-serial chip takes the data it receives via the PC USB connection and converts it back to serial UART TTL levels. Integrated level shifters assure that the programming signals are at the same level as your specific target microcontroller's operating voltage. The level shifted signals can directly be connected to the microcontroller's integrated UART and ISP mode pins - no RS232 transceiver required.

The board features a male header connection for (target) Vcc, GND, RX, TX, RST (switch to ISP mode for P89Vxx micros) and PO14 (ISP mode for LPC programming). Connect those pins to the appropriate pins on your microcontroller target and you're ready to program. See the user manual below for further details.

USB Programmer for NXP LPC and P89V51 Microcontrollers Package Contents

  • USB-to-serial programmer
  • 6 Pin Female to 6 Single Pin Female Target Cable
  • Note: A USB cable is not included. If you need a USB cable you can order one as an add-on option below

USB Programmer for NXP LPC and P89V51 Microcontrollers Downloads

User manual Please read this for full details on supported devices, required connections for programming and jumper settings.

FlashMagic software website


Optional Recommended Products for this Item
USB 2.0 Cable, 6ft., A-Male / B-Male+ US$6.00

This product was added to our catalog on Friday 20 August, 2010.

Reviews

Customers who bought this product also purchased
SOT23 to DIP 6-Pin Adapter PCBSOT23 to DIP 6-Pin Adapter PCBUS$1.50

SSOP-to-DIP 16-Pin Adapter PCBSSOP-to-DIP 16-Pin Adapter PCBUS$1.50

Logomatic v2 Serial SD DataloggerLogomatic v2 Serial SD DataloggerUS$59.95

Dual 5V/3.3V DC Regulator Board, 8-16V AC/DC Input (5V-3.3VReg)Dual 5V/3.3V DC Regulator Board, 8-16V AC/DC Input (5V-3.3VReg)US$11.90

USB-to-Serial Cable: 3.3V TTL, 6-pin SIP ConnectorUSB-to-Serial Cable: 3.3V TTL, 6-pin SIP ConnectorUS$16.50

18 ga. 1 (25.4mm) bent probe for vacuum devices18 ga. 1 (25.4mm) bent probe for vacuum devicesUS$2.00

Shopping Cart more
0 items
What's New? more
Electronic Speed Controller, HW30A, Pre-programmed for ELEV-8 V2
Electronic Speed Controller, HW30A, Pre-programmed for ELEV-8 V2
US$13.99
Specials more
XBee Explorer USB, Serial Access to XBee Pins, mini-USB
XBee Explorer USB, Serial Access to XBee Pins, mini-USB
US$24.95
US$18.00
Tell A Friend
 

Tell someone you know about this product.
Notifications more
NotificationsNotify me of updates to USB Programmer for NXP LPC and P89V51 Microcontrollers
Reviews more
Write ReviewWrite a review on this product!
  Monday 20 October, 2014   List of all our Products

Copyright © 2003-2014 MicroController Pros LLC
Powered by osCommerce